PDF download Download Article PDF download Download Article

Graphene is the wonder material of the century. Considering its relative strength compared to its weight, it is harder than steel and diamonds and also the best conductor of heat and electricity. And it's only 1 atom thick! You can make your own graphene at home, but be aware that it is more on the experimental level—you won’t be able to produce quantities large enough to do anything with. If during your experiment you find a cost-effective way to mass-produce the graphene, you could become rich and famous!

Method 1
Method 1 of 2:

Using the Sticky Tape Method

PDF download Download Article
  1. Start out by drawing just a small polka dot or a 1 centimetre (0.39 in) line to get a feeling for the process. Go over the shape 2 or 3 times to get a nice, thick layer. [1]
    • Alternatively, you can purchase powdered graphite at your local department or home improvement store for about $10.00 for 6 ounces (170 g). Use tweezers to place a small amount of the powder onto the piece of paper. A pinch would be too much. [2]
  2. Watermark wikiHow to Make Graphene
    Position the tape over the graphite so that the graphite will be about three-quarters of the way down the tape. Press the tape down on the graphite and then gently peel it off of the piece of paper. [3]
    Advertisement
  3. Watermark wikiHow to Make Graphene
    Grasp the tape on the edges and only fold it enough to cover the graphite. If you fold it completely in half, it will be difficult to open it up and pull it apart again. [4] Here, you are splitting the layers of graphite and separating the carbon atoms—which is necessary to get graphene. [5]
    • Alternatively, you may place a fresh piece of tape on top of the original piece and then peel it off.
  4. Watermark wikiHow to Make Graphene
    Each time you peel the tape off, the graphite layers get thinner and thinner. After about 20 times of peeling, you should end up with a layer of graphite that is only 1 atom thick. This is graphene. [6]
    • If you are using fresh pieces of tape, rather than folding, place the third piece of tape on top of the second piece; the fourth piece of tape on top of the third, and so on. [7]
  5. Place the piece of tape, sticky side down, on a microscope slide. View the slide between 100x and 400x magnification. If you used the same piece of tape folded on top of itself multiple times, you will notice that some spots will be darker and some will be lighter. The lighter spots are the thinnest layers and the lightest spot is the graphene. [8]
    • If you used fresh pieces of tape to peel layers each time, use your final piece of tape (about the 20th piece) to place under the microscope.
  6. Advertisement
Method 2
Method 2 of 2:

Using a Kitchen Blender

PDF download Download Article
  1. Watermark wikiHow to Make Graphene
    If you don’t have graphite powder, you can make some by pulverizing a few pencil leads in a pulverizer or grinder. [9] Use a high-power kitchen blender of at least 400 watts to get the best results. [10]
    • Be aware that you can no longer use this blender to make food or drinks after using it with graphite.
  2. Watermark wikiHow to Make Graphene
    The detergent acts as a surfactant which works to suspend the graphene particles in the mixture. It also prevents the particles from clumping together. [11] The brand of dish soap you use doesn’t matter, however, the amount you add to the mixture does.
    • The exact amount of dish soap that’s needed depends on the properties of the graphite powder and whether there are any other contaminants in the sample. Unfortunately, these factors cannot be known without the use of advanced lab equipment. [12]
    • Experiment with adding amounts within the 10–25 millilitres (0.34–0.85  fl oz) range to start, and then do additional experiments by adding either more or less soap.
  3. Watermark wikiHow to Make Graphene
    As the graphite is blended, it will create a black liquid that may be frothy. Eventually you will begin to notice tiny flakes forming on the surface of the liquid and on the side of the blender. [13]
    • Without lab equipment, it is difficult to distinguish between actual flakes of graphene and small flakes of graphite. In general, if the graphene particles are too big (still graphite), they will sink to the bottom of the blender; if they are smaller, they will float to the top. Particles that are suspended mid-water are nanoparticles, and are definitely graphene. [14]
  4. In a lab, they centrifuge the mixture to separate the graphene from the liquid. [15] Since it is unlikely that you have access to a centrifuge, simply pour the liquid mixture into a glass jar and let it sit for a few days. [16]
    • This resting period will allow the graphene to separate from the larger particles of graphite.
  5. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Why cant I use the blender anymore after I blend graphite?
    T. Chinsen
    Top Answerer
    Th fine graphite residue in the blender is difficult to remove completely. Anything processed after the graphite will pick up the residual particles. Any food item may end up with a graphite flavor, as the fine particles with behave like salt.
Ask a Question
      Advertisement

      Things You’ll Need

      • Lead pencil
      • Powdered graphite
      • Tape
      • Kitchen blender
      • Dishwashing liquid

      Tips

      • Making graphene at home is mostly just a proof-of-concept. It is unlikely that you will be able to make enough high-quality graphene to be of any productive use. But it’s a fun experiment! [17]
      • Since making graphene at home is largely experimental, the exact measurements for creating it in a blender is unknown. The measurements listed here are based off of one group of researcher’s findings.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      About This Article

      Article Summary X

      To make graphene, start by using a lead pencil to deposit a layer of graphite onto a sheet of paper, going over it 2-3 times to make it as thick as possible. Next, place a 2-inch piece of sticky tape face down on the graphite, pressing down gently. Fold the piece of tape in half, then peel it back apart. Repeat this folding and peeling process 20 times, making the graphite layer thinner and thinner until you’re finally left with graphene. To learn how to make graphene using a blender and graphite powder, keep reading!

      Did this summary help you?
      Thanks to all authors for creating a page that has been read 76,137 times.

      Did this article help you?

      Advertisement