Download Article
Download Article
What would a bookmark be without the familiar tassel to keep it from getting lost between the pages? If you want to add a tassel to a bookmark that you have made , or if the tassel in your favorite old bookmark has disintegrated, you can make your own tassel in a few minutes with a bit of string or cord.
Steps
Download Article
-
1Work around a wide ruler or a piece of stiff card (such as from a cereal box). Cut or fold it to an appropriate width, about 1.5 inches (4cm). You can adjust the length of the tassel by making this object wider or narrower.
- If in doubt, start with a card that's a little wider than you want. You can always trim the ends shorter later.
-
Wrap the string, cord, or yarn around the ruler or card several times. The number of loops, along with the thickness of the string, determines the thickness of the tassel.Advertisement -
3Cut the end of the string off the loops and cut a second piece of a generous length, perhaps a yard (90cm) or more. Fold this second piece in half.
-
Thread the folded end of the second string under the loops. There should be no need to use a needle. You should have a short loop on one side and two long tails on the other side. -
Pull the two long tails through the short loop. -
Tighten this knot snugly by pulling on the two long ends. Then slide the tassel off the ruler or card. -
7Thread both loose ends through a large needle.
-
Double the two loose ends , leaving about a four inch (10cm) loop. -
Push the needle through the top of the tassel and out the side. -
Wrap the free ends several times around the tassel , a little ways down from the first knot. Wrap tightly, and aim for even loops, forming a small, round ball. -
Push the needle down through the center of these loops from top to bottom. -
Pull the two long tails all the way through and tighten the knot firmly. -
Cut open the bottoms of the loops from before. -
Trim the ends to an even length. -
Insert the tassel in the bookmark by threading the loop end through the hole. -
Pass the tassel through the looped ends, and tug gently. -
Enjoy your new tassel.
Advertisement
Community Q&A
Search
-
QuestionWill this work on corner bookmarks?Community AnswerCorner bookmarks often slide on to the page, and adding a hole and a tassel may block the page from sliding in. However, if you add a small section of paper to your corner bookmark that hangs out of the book, it is possible to add a tassel. Just be careful, as regular printer paper may not be that strong and probably wouldn't last very long, so maybe use a thicker paper or material.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Crochet cotton will hold together with a simple knot like this, but if you think your cord or floss is too slippery, make a couple more knots before bringing the string down through the middle of the tassel. Or, work a dot of glue into the knot to keep things snug.Thanks
- This is very similar to a basic tassel, but it includes some extra loops to make it work for a bookmark.Thanks
- For an added touch, string the loops of the finished tassel through an interesting bead or two before placing the tassel on the bookmark.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- String or cord in any color of your choice. The string used here is crochet cotton, available in most craft stores and in many different colors. Leftover scraps of yarn also work well, provided they are not too thick.
- Scissors
- Card or ruler
- Tapestry needle or large sewing needle
- Bookmark with hole or card and hole punch.
About This Article
Thanks to all authors for creating a page that has been read 318,949 times.
Advertisement
84%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
