PDF download Download Article PDF download Download Article

Remote control cars are one of the toys of childhood that can still be enjoyed by adults. Why buy a brand new RC car when you can make your own? This tutorial will show you how to make a very basic one-direction toy car, meaning that it can only go forward and backward. Also, note that this not wireless like actual RC cars, so it will have a long wire attached to the car.

Part 1
Part 1 of 4:

Building the Wheels

PDF download Download Article
  1. 1
    Poke a tiny hole through the plastic bottle cap, small enough for the rod to fit in.
  2. Electrical tape is useful here since it provides a rubbery grip around the wheel.
    Step 2 Wrap the bottle cap edges with tape.
    Advertisement
  3. Step 3 Repeat the process 3 more times to the get 3 more wheels.
  4. Insert the 4-inch rod into both wheels and make sure the rod is exposed at both ends.
    Step 4 Take a straw and cut the ends so it’s shorter than 4 inches to cover the rod.
  5. Let it dry.
    Step 5 Glue the rod to the wheels.
  6. Glue the other 2 wheels to the rod, and let it dry. This will allow the motor to turn the rods thus spinning the wheels.
    Step 6 Insert a tiny gear to one side of the other exposed rod.
    Step 6 Insert a tiny gear to one side of the other exposed rod.
  7. Advertisement
Part 2
Part 2 of 4:

Constructing the Body

PDF download Download Article
  1. Glue both rods to the sticks.
    Step 1 Place 2 popsicle sticks next to each other.
  2. Step 2 Wait for the glue to dry.
  3. Step 3 Insert the tiny gear into the shaft of the DC motor.
    • The shaft is the thin rod of the motor.
  4. Align the gear of the motor to the gear of the rod perfectly so when one gear moves the other gear will move as well. Glue the motor and wait for it to dry.
    Step 4 Flip the car upside down so the rods are facing up.
  5. Advertisement
Part 3
Part 3 of 4:

Wiring the Car

PDF download Download Article
  1. 1
    Familiarize yourself with the equipment. These steps will require you to have basic knowledge on how to solder.
  2. Notice that there are two wires attached red (+) and black (-). These wires are tied to the DC motor that is supplying power.
    Step 2 Take a 9V battery clip buckle.
  3. Then place a hot soldering iron and melt the solder wire over the knot to permanently connect the two wires.
  4. 4
    Repeat this process as needed to extend the wire length. Remember that you should connect red wires to red wires and black wires to black wires.
  5. Take the end of the red wire and solder it to the top hole of the motor (positive eyebolt). Repeat this process for the black wire, soldering it to the bottom hole (negative eyebolt).
  6. 6
    Test it. Snap the clip buckle at the end of the wires to the 9V battery. If everything is done correctly, the shaft will spin clockwise making the car move forward.
    • Note: On the clip buckle, the smaller terminal is positive and the larger terminal is negative. When attaching the larger negative terminal of the clip buckle to the smaller positive terminal of the 9V battery and vice versa, the shaft spins clockwise, causing the car to move forward.
    • Likewise, when placing the larger negative terminal of the clip buckle close to the larger negative terminal of the 9V battery, the shaft spins counter clockwise, causing the car to move backward.
  7. Advertisement
Part 4
Part 4 of 4:

Controlling the Car

PDF download Download Article
  1. Attach the larger negative terminal of the clip buckle to the smaller positive terminal of the 9V battery and vice versa. This will enable the car to move forward.
  2. Place the larger negative terminals and smaller positive terminals of the clip buckle and the 9V battery on top of each other. This will enable the car to move backward.
  3. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Things You'll Need

      • A DC motor
      • Wires
      • Glue
      • Soldering kit
      • 9V battery
      • 9V battery clip buckle
      • Popsicle sticks
      • Bottle caps
      • Tape
      • Tiny gears
      • A 4-inch rod
      • Straws


      About This Article

      Thanks to all authors for creating a page that has been read 53,528 times.

      Did this article help you?

      Advertisement