PDF download Download Article PDF download Download Article

If your old Xbox is starting to fail and you’re thinking about repairing it yourself, or you want to install a modchip in it, the first step is opening the case. Luckily, with the right tools, opening the Xbox case is only a short process. Follow this guide to learn how.

Part 1
Part 1 of 3:

Opening the Case

PDF download Download Article
  1. Unplug the console from both the television and its power source.
  2. The bottom side of the Xbox is covered with manufacturer warning stickers. You will be removing the feet and stickers to reveal six screws.
    Advertisement
  3. There is a rubber foot in each corner. Use a flathead screwdriver to pry the feet from the case. Under each foot, you will find a screw.
  4. You should see a screw under each sticker. You can save the stickers by attaching them to wax paper.
  5. Torx screwdrivers have a 6-point star shape and the screws are commonly used in computer equipment and other electronics.
    • Set the screws aside so that you don’t lose track of them.
  6. Remove the top by pulling up while gently shaking. The entire top part of the case should come directly off. If you are having difficulty removing it, check to make sure that you removed all six screws from the base.
  7. Advertisement
Part 2
Part 2 of 3:

Removing the Drives

PDF download Download Article
  1. If you're facing the front of the Xbox, the hard drive should be on the right and the DVD drive should be on the left. The hard drive is most likely shiny, and the DVD drive is most likely dull gray with a yellow sticker on it.
  2. Grip the connector firmly on each side and pull it straight back from the hard drive. The cable might be snug and difficult to remove. Rock it back and forth if you are having difficulty pulling it straight out.
  3. You can find this screw on the divider between the hard drive and the DVD drive.
  4. Once you remove the Torx 10 screw holding it in, you can pull the tray holding the hard drive directly out of the case.
    • The hard drive is attached with a power cable. You most likely won’t need to remove the power cable to remove the hard drive from the case, but if you are swapping out the hard drive you can pull the cable directly out from the hard drive.
    • You can remove the hard drive from the tray by unscrewing the small screws that hold it in.
  5. Remove the cable the same way that the hard drive’s cable was removed. Pull it directly out from the DVD drive.
  6. There are two screws holding the DVD drive in, one on each side of the DVD drive.
  7. Once the IDE cable and screws have been removed, you can pull the drive straight up and out of the case.
  8. Pull it directly out of the drive. Be careful when removing the power cable as it is Xbox-specific and can be difficult to replace.
  9. Advertisement
Part 3
Part 3 of 3:

Removing the Motherboard

PDF download Download Article
  1. The motherboard is the large green board that all of the drives are connected to.
  2. It unplugs from the motherboard the same way that it did for the DVD and hard drives.
  3. Grip the large connector firmly and pull one side up at a 45°angle, then pull the other side up. It will be difficult to remove if you try pulling straight up. You can grip the connector with pliers if you have difficulty.
  4. There are two connectors that will need to be removed in order to pull the motherboard out. Remove each connector and make note of where it was plugged in.
    • There is a yellow cable connecting the motherboard to the case fan, the power switch and the reset switch.
    • There is also a cable that connects the USB ports to the motherboard.
  5. These screws are located in various places around the board. If you are looking at the motherboard from the front of the Xbox, five screws are located above the CPU fan, five screws are located below, and one screw is several inches to the right of the fan.
    • Remove the screws with a Torx 10 screwdriver.
  6. Place your fingers around the edges inside the case and lift straight up and out. Be sure to set the motherboard somewhere where it won't get damaged while it is out of the case.
  7. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Video

      Tips

      • You can preserve the stickers by placing them on strips of wax paper.
      • Place your loose screws from the various components in different places on your workspace so you don't confuse them. Arranging them in the same configuration in which you removed them will make reassembling the Xbox much easier.
      • A screw grabber uses a magnet to grasp the tiny metal screws, making them easier to control.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • Opening your Xbox voids your warranty with Microsoft. Do not attempt to open or fix your Xbox if you can send it to the manufacturer for repairs.
      Advertisement

      Things You'll Need

      • Xbox
      • Torx 20 screwdriver
      • Torx 10 screwdriver
      • Utility knife
      • Wax paper (optional)
      • Screw grabber (optional)

      About This Article

      Thanks to all authors for creating a page that has been read 126,728 times.

      Did this article help you?

      Advertisement