The serpentine belt in most modern vehicles transfers power from the crank pulley to the various accessories mounted on the engine. A worn or damaged serpentine belt can fail to adequately transfer the power, leaving your alternator, power steering, and air conditioning failing to function. If your serpentine belt needs to be replaced, it can be done using only common hand tools.
Steps
Get Car Support Solve Any Problem
Try Asking:
We’re sorry we don’t support the car you are looking for. Please enter its make, model, and year below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
-
Pull the hood release inside the cabin of the vehicle. To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver's side of the vehicle.- With the hood released, you will also need to release the safety latch located at the front of the vehicle.
- If you are having difficulty locating the hood release or safety latch, refer to your owner's manual for guidance.
-
Disconnect the battery. You should always disconnect your battery before starting an automotive project. Use the appropriate sized wrench or socket to loosen the nut holding the black ground cable on the negative terminal of the battery.- Slide the cable off of the terminal and tuck it to the side of the battery.
- You will not need to disconnect the positive terminal.
Advertisement -
Locate the serpentine belt. Depending on the engine in your vehicle, the serpentine belt may be located at the front of the engine bay, or it may be along one side. [1] X Expert Source Duston Maynes
Automotive Repair Specialist Expert Interview. 14 July 2021. There may be engine covers in the way, so be prepared to remove them if need be.- Engine covers may be held in place by plastic clips, so take care not to break them as you remove the covers.
- If you cannot find your serpentine belt, refer to the service manual for your specific vehicle.
-
Look for signs of damage or wear on the belt. Once you have located the serpentine belt, inspect it visually for signs of damage. If the belt is frayed, coming apart, or has marks that indicate that it has been rubbing on something, it will need to be replaced. [2] X Expert Source Duston Maynes
Automotive Repair Specialist Expert Interview. 14 July 2021. It is usually easy to determine if a belt needs to be replaced, as they tend to crack or lose chunks when they are overworn. [3] X Research source- Most serpentine belts need to be replaced every 40,000 to 70,000 miles.
- If there are signs of the belt rubbing on something, make sure to identify and repair whatever it was rubbing on to avoid damaging the new belt.
-
Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run.- Look in the owner's or service manual for your specific year, make and model vehicle for a diagram.
- You can also take a picture of the existing belt with your cell phone to use as a guide when installing the new one.
Advertisement
-
Determine if there is a belt tensioner pulley. Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. [4] X Research source- If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.
- Refer to your vehicle's service manual to confirm what type of tensioner your vehicle uses if you aren't sure.
-
Use a wrench to relieve the auto tensioner. Auto tensioners have either a hole that will fit a half inch drive ratchet, or a bolt you can use a socket to apply pressure to. Insert the wrench or place the socket over the bolt on the tensioner and twist it away from the belt to relieve the tension on it. [5] X Research source- Depending on the positioning of the tensioner pulley you may need to twist the tensioner clockwise or counterclockwise.
- Be sure to use the right size socket to avoid stripping the bolt head on the tensioner.
-
Loosen the bolts in the alternator bracket. If your vehicle uses the alternator bracket to apply tension to the belt, loosen the two bolts that pass through the long eyelets on the bracket. As you loosen the bolts, the tension on the belt will likely move the alternator toward the engine and relieve the pressure. [6] X Research source- Loosen the bolts enough to move the alternator, but don't remove them.
-
Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. [7] X Research source- If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.
Advertisement
-
Compare the new belt to the old one. Look at the new belt in comparison to the old one to be sure they are the same width and have the same number of ribs going across the belt horizontally. The old belt may be slightly longer than the new one due to stretching. [8] X Research source- If the new belt is not the same width as the old one, it is the wrong belt.
- Make sure the new belt doesn't show any signs of damage from the factory or it may tear after you install it.
-
Route the belt through the pulleys. Run the new belt through the pulleys in exactly the same way the old one was. Refer to the belt diagram in your vehicle's owner's manual or the picture you took of the belt before removing it to guide you. [9] X Research source- The belt should be long enough to route around all of the pulleys except the tensioner until you relieve the pressure on it.
- If the belt is loose after routing it, it is either the wrong size belt or you've routed it incorrectly.
-
Apply pressure on the auto tensioner and put the belt over it. Use the same wrench to loosen the auto tensioner pulley, then pull the belt over it. Once the belt is in place, release the pressure on the tensioner so it holds the belt in place. [10] X Research source- It may be difficult to apply pressure to the tensioner and route the belt, so you may want to ask a friend to help.
-
Increase the tension on the belt. If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension. [11] X Research source- You may need help tightening the bolts as you apply pressure to the alternator.
- Be careful not to pry against anything plastic in your engine bay to avoid breaking anything.
Advertisement
Expert Q&A
Search
-
QuestionHow do I know if I need to replace my serpentine belt?Duston Maynes is an Automotive Repair Specialist at RepairSmith. Duston specializes in leading a team that handles a variety of automotive repairs including replacing spark plugs, front and rear brake pads, fuel pumps, car batteries, alternators, timing belts, and starter motors. Duston holds an Associate’s degree in Automotive/Diesel Technology from The Universal Technical Institute of Arizona and is a Certified Diagnostic Technician and Automobile Mechanics Technician through BMW STEP. RepairSmith received The 2020 Big Innovation Award by Business Intelligence Group and The Startup of the Year by the American Business Awards. RepairSmith was also included in Built in LA’s 50 Startups to Watch and The Business Intelligence Group’s 52 Names Leading the Way in Customer Service. RepairSmith offers in-home services to provide car owners convenient and complete auto repair everywhere.Although serpentine belts last quite a bit, it's important to check on them every once in a while. To see if there's any problem, check if the outer side of the belt is looking glassy and if the inside of the belt is cracking. These are both good indicators that the serpentine belt needs to be replaced.
-
QuestionWhat happens if the serpentine belt breaks?Duston Maynes is an Automotive Repair Specialist at RepairSmith. Duston specializes in leading a team that handles a variety of automotive repairs including replacing spark plugs, front and rear brake pads, fuel pumps, car batteries, alternators, timing belts, and starter motors. Duston holds an Associate’s degree in Automotive/Diesel Technology from The Universal Technical Institute of Arizona and is a Certified Diagnostic Technician and Automobile Mechanics Technician through BMW STEP. RepairSmith received The 2020 Big Innovation Award by Business Intelligence Group and The Startup of the Year by the American Business Awards. RepairSmith was also included in Built in LA’s 50 Startups to Watch and The Business Intelligence Group’s 52 Names Leading the Way in Customer Service. RepairSmith offers in-home services to provide car owners convenient and complete auto repair everywhere.The belt can get caught in the crank, obstructing the system and damaging the motor.
-
QuestionHow do I replace the crank shaft pulley?Community AnswerIt's impossible to say without knowing the year, make, or model of your vehicle. You should be able to do a search online to find some tips on replacing parts for your specific vehicle.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
References
- ↑ Duston Maynes. Automotive Repair Specialist. Expert Interview. 14 July 2021.
- ↑ Duston Maynes. Automotive Repair Specialist. Expert Interview. 14 July 2021.
- ↑ http://www.testingautos.com/drive-belt-replaced
- ↑ http://www.familyhandyman.com/automotive/changing-a-car-serpentine-belt/view-all
- ↑ http://www.familyhandyman.com/automotive/changing-a-car-serpentine-belt/view-all
- ↑ http://www.familyhandyman.com/automotive/changing-a-car-serpentine-belt/view-all
- ↑ http://www.familyhandyman.com/automotive/changing-a-car-serpentine-belt/view-all
- ↑ http://www.popularmechanics.com/cars/how-to/a4121/4311197/
- ↑ http://www.popularmechanics.com/cars/how-to/a4121/4311197/
About This Article
Article Summary
X
To replace a serpentine belt, start by locating the old belt at the front or side of your engine bay. Then, use a wrench to relieve the auto tensioner so you can pull the belt off of the pulley system. If your vehicle doesn't have an auto tensioner, look for an alternator bracket and loosen the bolts in it instead. Next, get a new serpentine belt with the same width and number of ribs as the old one, and route it through the pulley system. Finally, apply tension to the new belt by tightening the auto tensioner or alternator bracket. To learn how to tell if an old serpentine belt needs to be replaced, scroll down!
Did this summary help you?
Thanks to all authors for creating a page that has been read 221,056 times.
Advertisement
"I'm grateful it didn't take long."
