Replacing the ink cartridge in your HP Officejet Pro 8600 is considered a routine printer maintenance procedure. When your HP Officejet printer runs out of ink, you can replace the ink cartridge yourself by accessing the printer’s cartridge compartment and removing the old ink cartridge.
Steps
-
Verify that your HP Officejet Pro is powered on. The printer must be turned on when replacing the ink cartridge. [1] X Expert Source Mitch Harris
Consumer Technology Expert Expert Interview. 31 August 31 2021. -
Place your fingers into the slot located at the left side of the printer, then pull forward to open the door to the cartridge compartment. [2] X Expert Source Mitch Harris
Consumer Technology Expert Expert Interview. 31 August 31 2021. The printer’s carriage will move to the left side of the printer while the cartridge compartment is opened.Advertisement -
Wait for the printer’s carriage to stop moving and become completely silent.
-
Push in on the front part of the ink cartridge to release that specific cartridge. [3] X Expert Source Mitch Harris
Consumer Technology Expert Expert Interview. 31 August 31 2021. -
Remove the old ink cartridge by pulling it toward you out of the slot.
-
Hold the new ink cartridge so that the contacts on the cartridge are facing toward the printer.
- When adding the new cartridge, make sure you remove any tape or other materials designed to protect the print heads. [4]
X
Expert Source
Mitch Harris
Consumer Technology Expert Expert Interview. 31 August 31 2021.
- When adding the new cartridge, make sure you remove any tape or other materials designed to protect the print heads. [4]
X
Expert Source
Mitch Harris
-
Gently push the new ink cartridge forward into the slot until it clicks into place. The colored dot on the cartridge label must match the color of the dot displayed on the slot.
-
Close the door to the cartridge compartment.
-
Wait for the printer to complete its warm-up sequence and become quiet. You may now begin using your Officejet Pro 8600.
Advertisement
Community Q&A
Search
-
QuestionWhat do I do if I changed the cartridges and my printer won't print?Community AnswerDouble check to make sure the cartridges are fully installed. If they are not snapped in completely, and some ink cartridges are hard to get in, they won't work. Hold the back of the printer, and push the replaced cartridge in as hard as you can. Try printing again.
-
QuestionWhat do I do if my printer is running lines of color down the page?Community AnswerClean the printheads through the printer's driver software. Go into the HP Officejet Pro 8600 program, and click "maintain your printer". The option to clean the printheads should be in there, and you can also print a diagnostic page from the "maintain your printer" menu, to see if you need to do anything else.
-
QuestionWhat do I do with the used cartridges?Community AnswerMost office supply stores have bins for recycling used cartridges, you can deposit your old cartridges here.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Warnings
- Never lift the carriage’s latch handle to insert new ink cartridges, as this action could result in damage to the printing mechanism and trigger printing problems.Thanks
Advertisement
References
- ↑ Mitch Harris. Consumer Technology Expert. Expert Interview. 31 August 31 2021.
- ↑ Mitch Harris. Consumer Technology Expert. Expert Interview. 31 August 31 2021.
- ↑ Mitch Harris. Consumer Technology Expert. Expert Interview. 31 August 31 2021.
- ↑ Mitch Harris. Consumer Technology Expert. Expert Interview. 31 August 31 2021.
About This Article
Thanks to all authors for creating a page that has been read 152,281 times.
Reader Success Stories
- "It was great. I was having difficulty inserting color inkjets, wasn't sure I was doing this right. Have changed before with no difficulty. Checked your guide then got a flashlight, made sure everything was in line. I moved white triangles to the right and tried again, inserted them really easily." ..." more
Advertisement