How to Replace a Refrigerator Water Valve: A Complete Repair Guide

PDF download Download Article
PDF download Download Article

The water inlet valve is an electronically operated device that connects the household water supply to your fridge if you have an icemaker and/or water dispenser. This valve is usually located at the back of the fridge near the bottom. It supplies water to the dispenser and water the icemaker. The electronic part of the valve can become faulty over time, resulting in such problems as the water dispenser not working, water leaking from the bottom of the fridge or the icemaker not making any ice. Replacing a water inlet valve in a refrigerator is usually a simple process.

Get Product Support Solve Any Problem

wH
Hi there! Do you have a question about how to use or repair your home appliance? I’ve read the manuals so you don’t have to. Select your product, brand, and model, then ask away!
*
*
1

Pull the refrigerator away from the wall.

PDF download Download Article
  1. Move the fridge so it's easier to get to to valve. Pull the refrigerator forward so that you can get behind it with ease to change the part. Before messing with the back, be sure to unplug the refrigerator and turn off the water supply.
    2. Advertisement
2

Remove the cardboard cover on the back of the fridge.

PDF download Download Article
  1. Taking off the fridge's back will give you access to the valve. Locate the screws in the upper right hand corner of the refrigerator and use a nut-driver to remove them. Depending on your model, there will probably be 2 or 3 screws.
    • When removing these screws, make sure that you don't lose them. It's highly recommended that you place them in a small plastic container.
3

Remove the backing of the valve.

PDF download Download Article
  1. Use a screwdriver to remove the machine screws holding the water valve to the cabinet. Once these screws have been removed, you should be able to pull the valve outside of the cavity, allowing access.
    2. Advertisement
4

Disconnet the electrical harnesses.

PDF download Download Article
  1. Behind the water valve, you will have to disconnect the two electrical harnesses. Each harness will have two different pin sizes. When the pins have been removed, slightly pull the tubing out. When doing so, it's normal to see some water spill out.
5

Clean the tubing when it's removed.

PDF download Download Article
  1. Clean up the rough edges of this tubing by cutting a bit of it off. To cut it, use a block of wood and putty knife on the floor. (Try to trim it and avoid cutting too much off.) Set this tubing aside.
    2. Advertisement
6

Purchase your new replacement valve.

PDF download Download Article
  1. Use the old valve to help purchase the replacement. You may notice an extra piece on it; depending on the model of your refrigerator, you may or may not need this piece. If your existing piece had that additional part, keep it on. However, if it didn't, it's okay to snap it off.
7

Reinsert the tubing.

PDF download Download Article
  1. Lightly push the clean tubing in to ensure the new tubing snaps into place. When inserting the tubing, just make sure that it's firmly in place and doesn't move around when you poke at it, and that it is snug.
    2. Advertisement
8

Reinstall the terminals.

PDF download Download Article
  1. Each pin will be a different size, so it'll be impossible to mix up the connections.
9

Return everything to its place and turn on the water.

PDF download Download Article
  1. Reinstall the screws and tuck the tubing out of the way. Turn on your water supply to make sure there are no leaks. If there are no leaks, you can safely put the back cover back on using those screws you set aside in the plastic container.
    2. Advertisement
10

Plug in the refrigerator.

PDF download Download Article
  1. Push the refrigerator into place and your water inlet valve should be working like new.

Community Q&A

Search
Add New Question
  • Question
    Is it possible for the water dispenser to work but not the icemaker?
    Community Answer
    Yes, it is possible. There is probably an issue with the icemaking mechanism and not the water line.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 11
  • Question
    I replaced the solenoid water valve to the ice maker and door dispenser. Now neither is working. What should I check?
    Community Answer
    You either installed it wrong or you may just need to unplug the fridge for a full minute for the replacement to be reset.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 0
  • Question
    Where do I get the little round rings that are on the tubing?
    Community Answer
    Nowhere, you have to replace the entire water inlet valve, they're integrated into it.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 4
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • Use the small plastic container as storage for any screws removed so they don't get lost.
        Thanks
        Helpful 0 Not Helpful 0
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You'll Need

      • 1/4-inch nut driver
      • Screwdriver
      • Putty knife
      • Plastic container, small

      You Might Also Like

      How to
      Test an Evaporator Fan Motor
      How to
      Adjust Your Fridge to the Right Temperature
      Easy Steps to Remove & Replace a Fridge Door Seal
      3 Ways to Stop & Prevent Ice Build Up in Your Fridge & Freezer
      How to
      Put Freon in a Refrigerator
      How to
      Level a Refrigerator (With Leveling Feet or Rollers)
      How to
      Change the Side on Which Your Refrigerator Door Opens
      How to
      Move a Fridge (For Cleaning or a Long-Distance Move)
      How to
      Test a Refrigerator PTC Relay
      Why Your Refrigerator Is Freezing Your Food (And How to Fix It)
      How to
      Defrost a Samsung Ice Maker: A Quick Guide
      How to
      Remove a Scratch from a Stainless Steel Refrigerator Door
      Easy Methods to Reset Your Samsung Refrigerator
      How to
      Replace a Water Filter in a Kenmore Fridge
      Advertisement

      References

      1. https://www.partselect.com/Repair/Refrigerator/Leaking/ -- Research source from original author
      2. http://www.youtube.com/watch?v=eNGe_VUDIBA --Research source from original author

      About This Article

      Thanks to all authors for creating a page that has been read 50,823 times.

      Did this article help you?

      Advertisement