PDF download Download Article
Simple steps to connect your digital converter box and antenna to any TV
PDF download Download Article

This wikiHow teaches you how to install a digital converter box for your analog television set. Analog televisions that do not receive DTV digital signals will not pick up most over-the-air channels without a digital converter box (DTV converter box), which receives over-the-air DTV digital signals and converts them into analog signals that can be shown on analog TVs.

Things You Should Know

  • With the TV turned off and unplugged, attach the antenna to the "IN" port on the DTV box.
  • Connect the DTV box to the TV using a coaxial or RCA cable.
  • Turn on the TV and DTV box, then go through the setup process.
  1. If you have an analog TV which can't receive cable, you'll need to install a digital converter box in order to translate the signal for your TV.
    • If you have an HDTV or a TV with "SDTV" written on the front of it, you do not need a digital converter box.
  2. Advertisement
  3. Unplug the antenna's coaxial cable from the back of your TV to do so. Don't worry about moving the antenna—you'll have to hook it up to the digital converter box in a minute.
    • This step also applies if you're using an externally mounted antenna (e.g., one on your roof).
    • If your TV doesn't have an antenna, you'll need to purchase a set of antennae (e.g., rabbit ears) before you can use your digital converter box.
  4. Your digital converter box will need to be close enough to the TV that it can still connect to the TV without having to stretch or bend any wires.
    • The digital converter box's front (i.e., the side with the lights and no cord) should be facing in the same direction as your TV.
  5. Using the antenna's coaxial cable, plug the antenna into the "IN" coaxial port on the back of the digital converter box.
    • If your antenna's coaxial cable screws into place, make sure you screw it in tightly before proceeding.
  6. You can do this using the coaxial cable that most likely came with your digital converter box, or you can use standard RCA (red, yellow, and white) cables:
    • Coaxial cable - Plug one end of the coaxial cable into the "OUT" coaxial port on the back of your digital converter box, then plug the other end of the cable into the "IN" coaxial port (the one that the antenna cable was plugged into) on your TV.
    • RCA cables - Plug the red, white, and yellow cables into the same-colored ports on the back of the digital converter box (e.g., the red cable plugs into the red port and so on), then plug the other ends of the cables into the same-colored ports on the front or back of your TV.
  7. Using the cord that's built into the digital converter box, attach the digital converter box to an electrical outlet or surge protector.
    • If your digital converter box doesn't have a built-in electrical cord, you'll have to attach the non-electrical plug end of the cord that came with the box into the back of the box.
  8. Some digital converter boxes have an "Off/On" switch on the back or the side of the frame; if so, flip this switch to the "On" position before proceeding.
  9. Most digital converter boxes will scan for digital channels when you switch to channel 3 or channel 4; if this doesn't work for you, you'll need to consult your digital converter box's manual in order to see which channel you're supposed to use.
    • If your digital converter box came with a remote, you'll need to put batteries in the remote, press the power button on the remote to turn on the box, and then use the remote's arrows to navigate through the digital converter box's on-screen setup.
    • Usually, you'll just have to select Next on-screen a few times until the digital converter box begins scanning for channels.
    • Check your digital converter box's manual if you're having trouble navigating through the setup process.
  10. Your digital converter box will scan for available digital channels in range; after the scan is complete, you'll be able to browse through these channels as you please.
  11. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Will a DTV converter box work on a non-digital TV?
    Community Answer
    The digital converter boxes were created to allow people to keep their non-digital TVs but receive the new digital TV signals. They are fairly simple to connect, and if you like old school things, you can still use a VCR (you must have two converter boxes if you like to watch one show and record another).
  • Question
    Do I need an indoor antenna for my Ematic converter box?
    Community Answer
    Possibly. It depends on the exact kind of converter box and the release date.
  • Question
    I have a satellite dish receiver on my roof, but it is dead as I withdrew my subscription due to too many commercials. Can I attach an outdoor HD antenna to it, since stations in either direction are over 100 miles away from my home in the mountains? Will I get any reception?
    Community Answer
    You can try. It might work, but make sure they are strong and have a shelter for the rain.
See more answers
Ask a Question
      Advertisement

      Tips

      • If using a DVD player as well as a converter box, the DVD player and the converter box must be attached to separate connections on the TV. S-video, composite, and component connections are commonly found on DVD players.
      • Many DVD players and speaker systems have optical audio connections that can be used in conjunction with composite or component video connections. This type of connection offers superior sound quality.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • Using a digital converter box in 2018 may be more inconvenient than simply purchasing a low-end HDTV.
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 489,960 times.

      Is this article up to date?

      Advertisement