PDF download Download Article PDF download Download Article

Snakes are quite common and generally unprotected in many parts of the world. While they do serve a purpose in nature, they also have delicious meat and possess skins that are often quite beautiful. [1] The following steps will tell you how to skin, eviscerate, and prepare a snake for cooking. If the subject is not a rattlesnake, these instructions should still be applicable, with the exception of the ones regarding the rattle.

  1. Most taxidermy projects require a different, more difficult method of skinning, but that method is not the focus of this article. It is always best to work with a decapitated snake because even "dead" snakes have been known to strike, and the fangs are still quite dangerous. By removing the head, you are removing all venom. [2]
  2. Soapy water or even plain water will work well. Just make sure the soap is completely rinsed off of the snake.
    Advertisement
  3. down the centerline of the belly, through the skin only, all the way from the stump where the head was attached to the base of the rattle. On most snakes, there is a smaller belly scale covering the cloaca. In the picture, this is the last cream-colored scale before the darker tail scales. Simply split this up the middle just like the rest of the scales. [3]
  4. from the flesh by hand, again beginning at the head end, using even tension on the skin to avoid tearing. Be sure to separate the skin from the membrane underneath right at the head end. You want clean skin with nothing attached to it. The hide should be loose enough that it easily detaches from the carcass. If the skin is a bit "tight", a knife may be used to carefully free it in the tough places. Peeling without the use of a knife can usually be accomplished all the way to the cloaca. [4]
    • When the cloaca is reached, it is usually necessary to free it from the skin by cutting around the opening with the knife. Continue skinning to the base of the rattle. The attachments to the muscles that control the rattle generally make the hide harder to pull off. A knife must be used in this area if the skin is too tight to peel off, as the skin is rather delicate in this section.
    • After the skin is completely freed from all but the rattle itself, cut through the tail as close to the base of the rattle as possible. If the skin is to be saved with the rattle attached, it helps for the piece of flesh attached to the rattle to be small.
    • Don't fret too much about totally removing the flesh below the cloaca and above the rattles (basically the black and white banding on rattlesnakes). It is almost impossible to completely remove the skin from the flesh in this area. It will dry up easily.
    • Constrictor snakes such as bull and rat snakes cannot be "peeled". Their skin is attached with many muscle attachments over the full length of the body. Cutting through them is tedious as it is hard to get the skin free from the flesh and very easy to cut or tear the skin.
  5. , starting at the head end, using a scooping motion with the hand if the organs are difficult to remove. Care must be taken near the lower digestive region or the snake might excrete unappetizing substances on the meat. [5]
  6. Membrane and fat are often rather difficult to remove from the ribcage and backbone and can be cut free at this time.
  7. [6]
  8. Advertisement

Community Q&A

Search
Add New Question
  • Question
    How long after I kill the snake can I skin it?
    Community Answer
    You should wait two to three hours, although some bigger snakes can take over three hours to settle.
  • Question
    How exactly do I cure the skin?
    Community Answer
    I simply scrape any remaining meat off the hide and chuck the whole thing in to a jar of glycerin and seal it. It cures in a couple of weeks and remains soft and supple afterwards.
  • Question
    What do I do with the snake's head?
    Community Answer
    You cut it off and dispose of it, unless you want to keep a part of it, like the fangs or skull. If you want to keep the skull, it's best to slowly scrape away the skin to make sure you don't damage the bone.
See more answers
Ask a Question
      Advertisement

      Video

      Tips

      • A simpler way to skin a snake is to remove the head and carefully peel the skin over itself like pulling a sock off your foot by pulling from the top. Sprinkle the skin with borax to cure it, around a week. You can then sew or glue it onto a hat or belt. The advantage to this is that you can't accidentally pierce the visceral sac, that scales are not broken and it is a more finished look when stitching the skin onto something.
      • Snakes can safely be frozen; the meat is not damaged and the coloration of the skin is not affected.
      • If the snake was bitten by itself or by another venomous snake, cooking will usually remove all venom. If you see any bite marks, however, proceed with caution.
      Show More Tips
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You'll Need

      • A fresh, suitable snake
      • A good, sharp knife (nearly any knife with a straight edge and a sharp point will work)

      About This Article

      Thanks to all authors for creating a page that has been read 268,834 times.

      Did this article help you?

      Advertisement