PDF download Download Article PDF download Download Article

Knowing how to properly tie together different lines is one of the most important parts of fly fishing. When it comes to tying together the tippet and leader lines, which are two lines of a similar diameter, there are two main knots that are commonly used. With a little practice, you’ll be able to use either the double surgeon’s knot or the blood knot to tie your leader and tippet together.

Method 1
Method 1 of 2:

Tying a Double Surgeon’s Knot

PDF download Download Article
  1. Position the lines with the tag ends facing in opposite directions. Hold the leader line and the tag end of the tippet together by pinching them between your thumb and forefinger on your non-dominant hand where they meet. [1]
    • Tag end refers to the end of the line that you are using to tie the knot.
  2. Use your dominant hand to create an overhand knot with the tag end of the leader, and pass the leader and tippet tag ends through the loop once. Do not tighten the knot all the way. It should be an open loop.
    • At this point the loop will look like a loose pretzel.
    Advertisement
  3. Hold the loop in your non-dominant hand. Twist the leader and tippet tag ends around the loop and pass them through again. Do not fully tighten the knot yet. [2]
    • The loop will now look like it has a small braid on the top side.
  4. Use saliva to moisten the loop. Pull the leader line and tippet tag end with your left hand, and the tippet line and leader tag end with your right hand simultaneously until the knot is fully closed.
    • Lip balm also makes a good moistener for the line if you don’t want to use saliva.
    • Pull each side slowly to tighten the knot evenly. [3]
  5. Use nail clippers, scissors, or pliers to clip the tag ends of the leader and tippet to finish the knot. Try to get them as short and close to the knot as possible so that there are no loose ends.
    • Once you learn this knot it is very strong and fast to tie! [4]
  6. Advertisement
Method 2
Method 2 of 2:

Using a Blood Knot

PDF download Download Article
  1. Hold them together in your non-dominant hand by pinching where they overlap. Keep your dominant hand free to tie the lines together. [5]
    • Tag end means the end of the line where you are tying the knot.
    • The blood knot can be used to tie any two lines of the same diameter together.
  2. Use your dominant hand to wrap one line in a coil, like a spring, around the other line. Then pull the tag end back and through the middle where the two lines meet. [6]
    • You can wrap one line around the other up to 7 times for a stronger variation of this knot.
  3. Repeat the coiling process for the other side. Pull the leader tag end back through the middle where the lines meet in the middle so that it is facing in the opposite direction of the tippet tag end. [7]
    • The knot will now look like it has two spring coils, one on either side. The tag ends will be facing opposite directions, one going out through the middle to the top and one to the bottom. [8]
  4. Take one line in each hand and pull them to close the knot. As you do this the twists will gather together and tighten. [9]
  5. Trim the tag ends so they are not long and loose. You now have a tight and strong knot holding the tippet and leader lines together! [10]
    • The blood knot is not quite as strong as the double surgeon’s knot, but it creates a straighter connection between the two lines, which can help when casting your line.
  6. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!

      About This Article

      Thanks to all authors for creating a page that has been read 91,201 times.

      Reader Success Stories

      • David Schwebach

        Jul 19, 2020

        "The illustrations were great and very easy and simple to do, so thank you."
      Share your story

      Did this article help you?

      Advertisement