Aikido is a modern Japanese martial art. The long fabric belt that Aikido participants wear—often called an “obi”—can be double the length of some participants’ bodies. Depending on an individual’s height and waist circumference, Aikido belts commonly range in length from 215 cm (84.6 in) to 315 cm (124 in). [1] X Research source To tie an obi, you’ll need to wrap the belt around your waist, then wrap the belt around your body and overlap the ends until you’re left with a diamond-shaped knot.
Steps
Part 1
Part 1 of 3:
Placing the Obi around Your Body
-
Find the mid-point of the belt. Begin by folding the belt in half. Make sure that the two ends of the belt are touching—if one side of the belt is longer than the other, your midpoint will be inaccurate. Once the two halves of the belt are even, the center of your fold will be the belt’s mid-point. [2] X Research source
- If you’re still new to tying an obi on yourself, practice in front of a mirror. This will make it easier to tell if the belt is lying as it should behind your back.
-
Wrap the belt around your waist. Place the mid-point of the obi in the middle of your stomach, just above your navel. Then, wrap the two ends of the belt behind your back. Make sure that that the belt crosses behind you in the center of your back. [3] X Research source
- Make sure that one of the sides of the obi is lying beneath the other. If the sides are lying parallel on your back, you won’t be able to tie the belt correctly.
Advertisement -
Bring the belt ends back in front of your body. Make the two sides of the obi overlap as much as possible. You’re essentially creating a double-thick belt which fully circles your waist. [4] X Research source
- At the end of this step, you should be left with one side of the belt in each hand, and the overlapping halves of the obi wrapped fully around your body.
Advertisement
Part 2
Part 2 of 3:
Weaving the Belt Ends
-
Cross the top side over the bottom. Holding the upper layer (side 2) of the obi in your left hand and the lower layer (side 1) in your right hand, cross left over right, so that the two sides of the belt form an “x” shape on your stomach. [5] X Research source
- Cross the belt as close to the center of your belly as possible. If the cross is to one side of your body or the other, the knot in your obi won’t be centered.
-
Tuck the left side of the obi under both layers of the belt around your body. The mid-point of the belt should still be centered above your navel. Take the upper side (2) of the belt (which has been in your left hand) and tuck this under up the belt’s mid-point, so it passes next to your body. Pull the side of the obi tight, so that no excess belt is hanging down below the beginning of the knot. [6] X Research source
- As you tie the knot, be sure to keep the belt flat. Never crunch, bend, or fold the flat obi when tying it.
-
Bend the tucked side of the obi so that it crosses the other side in front of you. Take side (2) of the obi and gently bend it down so that it crosses back over the knot that you’ve started to tie. Cross side (2) over side (1) in front of you. [7] X Research source
- The two sides of the belt should overlap a few inches in front of your body, leaving an open gap between the partially tied knot and the crossed sides of the belt.
Advertisement
Part 3
Part 3 of 3:
Finishing the Knot
-
Tuck end (1) through the gap in the knot. At this point, side (1) should be crossed under side (2) a few inches in front of your body. Take end (1) and pass it up and over side (2). Pass end (1) through the large gap that you formed when overlapping the two sides of the obi. [8] X Research source
- Leave the knot loose as you’re forming it. Do not try to tighten the knot until it’s completed, or you’ll have a very difficult time completing the knot.
-
Guide the rest of side (1) through the hole. Keep one of your hands on the point in front of you where sides (2) and (1) overlap, and use your other hand to guide side (1) of the belt through the gap where you put its tip in the previous step. [9] X Research source
- As you pull side (1) through the gap, keep it flat. Don’t allow the fabric of the belt to twist or fold, or you’ll end up with a messy knot.
-
Pull both sides outward to tighten the knot. Once you’ve pulled side (1) through the gap, the knot is ready to be tightened. Don’t try to tighten the obi knot by pulling one side up and one side down, or you’ll risk skewing the knot and giving it an asymmetrical look. [10] X Research source
- The tightened knot should have a roughly diamond-shaped appearance.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Depending on where you’re studying Aikido, the colors of the belt will vary. Traditional Japanese Aikido belts are only either white or black. Westernized Aikido schools—for example, in Britain or the United States—typically introduce several other colors which indicate a progression of rank. [11] X Research sourceThanks
Advertisement
References
- ↑ https://www.seidoshop.com/pages/obi-belt-size-chart
- ↑ http://www.aikidouk.co.uk/belt_tieing.htm
- ↑ http://www.aikidouk.co.uk/belt_tieing.htm
- ↑ https://www.youtube.com/watch?v=LhpSPALRXkg&feature=youtu.be&t=24s
- ↑ http://www.aikidouk.co.uk/belt_tieing.htm
- ↑ https://www.youtube.com/watch?v=LhpSPALRXkg&feature=youtu.be&t=33s
- ↑ https://www.youtube.com/watch?v=3RmnLsKacpQ&feature=youtu.be&t=1m13s
- ↑ http://www.aikidouk.co.uk/belt_tieing.htm
- ↑ http://www.aikidouk.co.uk/belt_tieing.htm
About this article
Thanks to all authors for creating a page that has been read 28,566 times.
Advertisement
