How to Wire a Baldor 3 Phase Motor

Wiring a Baldor motor can at first glance look to be a very intimidating task. Yet, with the help of this step by step guide, this task will be become as easy as counting to five. Now, for the purposes of safety, the steps listed below will ONLY demonstrate how to wire a motor for 240V. This should only be used as a basic guide for the process for wiring an AC motor. Please be aware that all steps on this page are subject to change depending on your motors configuration. The goal here is to provide a basic instruction set that will make any future project, whether at home or at work, that much easier to perform.

Steps

PDF download Download Article
  1. 1
    Check power source. Ensure that any electrical power fed into power cord, is shut off prior to working on motor.
  2. 2
    Prepare power cord. Using a pair of diagonal cutters, cut and remove 3 in of rubber insulation around outside of power cord. Revealing four wires inside cord.
    • Remove approx. 3 inches (7.6 cm) of insulation from the outside of the four lines located within the power cord.
    • Once for inner lines are visible remove approx. 1in. of insulation from the red, white and black lines, revealing copper wire.
    • Be aware that the power lines are referred to as: L1, L2, L3 respectively however there is no specific order to the power lines, meaning these tittles can be used interchangeably.
    Advertisement
  3. Connect ground wire to wire terminal. Using a crimping tool, connect ring terminal to the end of ground (green) wire.
  4. Using a flat head screwdriver remove four hex head screws securing cover plate of conduit box. This is located on the motor.
  5. Using standard wire connectors twist and connect wires in the following order:
    • 9 to 3
    • 8 to 2
    • 7 to1
    • 4 to 5 to 6

    Tip : When making the connections, trim the wires to a uniform length so they will “dress” into the box neatly. This prevents cramming the wires and making a mess.

  6. Feed exposed end of power cord through circular hole of conduit box.
  7. Connect power lines to wires located within motor by using standard wire connectors in the following order:
    • 9 to 3; L1
    • 8 to 2; L2
    • 7 to 1; L3
    • The ground (green) line is connected separately to a green ground screw located within the conduit box of the motor. (To do this remove screw completely, attach the ground wire to screw. Finally re-insert screw.)
  8. 8
    Check all connections. Ensure all of connectors and wires are tight and secure.
    • Tug on connectors lightly to confirm proper installation.
  9. 9
    Check continuity of connections. Using a multi-meter/electrical tester check the continuity of all connections, to do this:
    • Observe multi-meter/ electrical tester for any output of sound. If no sound is observed, place black test lead on a different pin, until sound is observed.
    • Repeat this process for every connection in conduit box.
    • If continuity does not exist on all four connections, PLEASE check connections to proper confirm installation.
  12. Using a flat head screwdriver insert and secure four hex head screws of cover plate to conduit box.
  13. 13
    Plug in motor to ensure proper function.
    • If the motor spins in the wrong direction, simply switch the location of two of the power lines, the will reverse the rotation of the motor.
    14. Advertisement

Community Q&A

Search
Add New Question
  • Question
    On a high-voltage motor with 10T, 11T, 12T as a dot and not going to anything on the wiring diagram, do I leave them all separate and not connected to anything?
    Community Answer
    On a 12-wire motor wired for high voltage (i.e., 480V), 10T, 11T and 12T must be connected together but not connected to anything else. The other 9 wires would be connected as in a 9-wire motor (note in a 9-wire motor, the equivalent of T10, T11 and T12 are internally connected together). L1 to T1, L2 to T2, L3 to T3, T4 to T7, T5 to T8 and T6 to T9. Note: a 9-wire motor can only be connected in a Wye configuration, whereas a 12-wire motor can be connected in either a Wye or Delta configuration. Both 9-wire and 12-wire motors can be connected for high- or low-voltage operation.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 1 Helpful 15
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • If you look on the side of the motor you will notice a small wiring diagram for the motor, feel free to use this as a frame of reference.
        Thanks
        Helpful 0 Not Helpful 0
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You'll Need

      • Wire Strippers
      • Diagonal Cutters
      • Multi-meter/ Electrical Tester
      • Screwdriver flat head: size 2
      • Standard wire connectors
      • Crimping Tool
      • Ring terminal
      • Gloves
      • Eye protection/ Safety glasses

      Expert Interview

      Thanks for reading our article! If you’d like to learn more about electrical wiring, check out our in-depth interview with Ricardo Mitchell .

      You Might Also Like

      How to
      Make a Simple Electric Generator
      How to
      Hook up a Generator to Your House: Installation, Safety, & More
      Checking an Electric Motor with a Multimeter (Plus, Troubleshooting Tips)
      How to
      Test a Transformer
      How to
      Check an AC Compressor
      How to
      Rewind an Electric Motor
      How to
      Test a Generator
      How to
      Put Oil in an AC Compressor
      How to
      Reverse an Electric Motor
      How to
      Make a Homopolar Motor
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 79,017 times.

      Did this article help you?

      Advertisement