What Kind of Reality Check Do I Need Quiz
Q&A for How to Make a Portable and Rechargeable USB Charger
Coming soon
Search
-
QuestionHow do I connect the batteries to the USB connector?Community AnswerUse a battery holder from an old remote or even a toy car that takes batteries. Just solder the wire from the battery holder to the USB connector and you are all set.
-
QuestionHow will I know if I did it wrong?Community AnswerWhen your phone isn't charging, then you have done it wrong.
-
QuestionCan I use lithium ion batteries instead?Community AnswerTheir voltage does not match by AAA. You could use them by adding a voltage controller (5 volt, 1 / 1.5 amp), then it would work.
-
QuestionCan I use the same amount of batteries if I want to put in two USB plugins?Community AnswerThat shouldn't be a problem, but you will see a decrease in charging rate for both devices when doing this. Try buying a small portable charger, especially if you need more ports, as this will be more consistent, safer for your devices, and will deliver power to both devices reliably.
-
QuestionCan four cells really charge a mobile phone?Community AnswerYes, they can if the cells are powerful enough.
-
QuestionDo I need a serial or parallel connection to do this with AAA batteries?Community AnswerYou might want to use a serial circuit so I suggest using a battery holder from an old remote or anything that uses batteries so that all the wiring is connected for you inside the battery holder.
-
QuestionHow can I tell if my rechargeable power bank is fully charged?Community AnswerThis might require more complicated tinkering with the setup. You might have to include a sensor to tell whether the batteries are fully charged, or include a sensor that measures how much power has gone through, then tells you when the correct amount has gone though. This might be a little more finicky though.
-
QuestionCan I use a plastic box instead of an Altoids tin?Community AnswerYes, it works just the same. Just make sure there is enough room to hold all parts.
-
QuestionDo I need to connect any voltage ic or transistor to charge a mobile phone?Community AnswerCheck your voltage. It should be 4.5 - 5 volt and 1 amp. If not, you will need a transistor or voltage controller.
-
QuestionCan I use cellphone batteries?Community AnswerYes. Just connect the USB connector wires to the first and last conductor plate on the cellphone battery.
-
QuestionCan I use a 3.5, 3.7 or 9 volts battery?Community AnswerYou need a voltage regulator that provides only 5 volts, 1 amp.
-
QuestionCan I use alkaline AA batteries instead?Alex NiculescuCommunity AnswerIn theory, yes, but you will lose the recharging ability, and it will be more complicated to make 1.5V batteries to output 5V.
-
QuestionCan I use AA batteries instead of rechargeable ones?Joval MangalanCommunity AnswerYou can use AA batteries, but the downside to that is the fact that you have to replace the batteries every time they run out, therefore rechargeable batteries are more cost effective.
-
QuestionHow can I tell if the battery system is truly rechargeable?Community AnswerRead the label on the battery. Most batteries will state whether they are rechargeable or not.
-
QuestionWhat kind of battery will I need to fully charge an iPhone?Community AnswerAA batteries can still be used for an iPhone. You just need a different port.
-
QuestionWhat type of batteries should I use?Community AnswerIt's recommended to use rechargeable AAA batteries, but you can use lithium ion batteries too. That way you don't have to make the male-to-male cable to charge it.
-
QuestionHow to check that batteries are fully charged or not?Community AnswerYou can use a voltmeter to test for the voltage. They can be found wherever electronics are sold.
-
QuestionCan I charge a laptop with a power bank via male-to-male USB?Community AnswerNo. As laptop batteries are much larger, they have greater voltage requirements than a cell phone charger can provide.
-
QuestionShould I solder the wires together when making a portable USB charger?Community AnswerYes. If you don't have a soldering station, then twist the cables and tape them together.
-
QuestionCan a USB charger work if I use AA batteries?Community AnswerYes, but you will need a voltage controller as AA have more voltage than AAA.
-
QuestionWhat is the amperage and volt output for this USB charger?Community AnswerThe voltage of the batteries should be about 5v and 1.5amp.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit