Download Article
Download Article
Gas powered engines and diesel powered engines ignite differently. Gas powered engines start when the fuel is ignited by a spark from a spark plug. In contrast, diesel engines are ignited by the heat caused by compression. In a diesel truck, the fuel and air must get hot enough to create combustion, which then creates the spark to start the engine. Because heat is necessary to start a diesel truck, the process for starting it is different than starting a gas engine. Follow these steps to start a diesel truck.
Steps
Download Article
-
Turn the key to the start position without turning the engine on. You will see the "wait to start" light on the dash. Do not attempt to start the engine until the light disappears. -
Wait for the glow plugs to heat up before attempting to start the truck. Heating the glow plugs takes up to 15 seconds. The "wait to start" light won't go out until the glow plugs are ready. During cold weather, the glow plugs will take longer to heat. [1] X Research source- Check the glow plugs or intake heater before the cold weather season to ensure your truck will start during cold days. A glow plug is a device with a heating element that heats up the air in the diesel truck to start the vehicle. Another method of heating the air is to use an intake heater. In cold weather, your diesel truck won't start without the assistance of 1 of these 2 parts.
- Get new batteries if necessary. Have 2 good batteries in the truck at all times. Diesel trucks have 2 batteries to start the engine and heat the glow plugs. If the batteries are in poor condition, the extra cranking of the engine to try to start it will affect the quality of the glow plugs, flood the engine and run down the batteries to the point that the engine won't start.
Advertisement -
Start the engine, but allow it to crank for no more than 30 seconds. If the truck doesn't start within 30 seconds, turn the key to the off position. -
Attempt to start the vehicle again by heating the glow plugs. This will require turning the key to the on position and waiting until the "wait to start" light goes out again. -
Turn the key to the start position and allow the engine to crank for no more than 30 seconds. If the engine doesn't start, turn the key to the off position and try the following:- Plug the truck into an electrical outlet. Diesel trucks have a 3-prong plug located under the front bumper or grill area. Using an extension cord, plug the truck into an outlet. You will hear the block heater turn on. When the glow plugs or intake heater aren't working properly, your truck won't start because there's no combustion. Plugging the truck in will allow the block heater to create the heat necessary for combustion to start the truck. [2] X Research source
- Leave the truck plugged in for at least 2 hours before you try to restart the vehicle. It will take this long to heat coolant in the engine block. If it still won't start, seek the assistance of a diesel mechanic.
Advertisement
Get Car Support Solve Any Problem
Try Asking:
We’re sorry we don’t support the car you are looking for. Please enter its make, model, and year below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
How Do You Start a Diesel Truck?
Expert Q&A
Search
-
QuestionHow do I start a semi-truck?Charley Helvy is an Automotive & Diesel Expert based in Avondale, Arizona. He is the founder of Charley’s Garage, an educational YouTube channel focusing on simple videos for automotive and truck enthusiasts. He has over 31 years of experience in the automotive world. He is a Diesel Instructor at the Universal Technical Institute and is a certified ASE Master Heavy Truck Technician. He offers training on gas and diesel engines on his YouTube channel, along with other DIY and explanation videos for beginners and enthusiasts alike. In 2024, he published a complete guide on Emissions Systems in Automotive and Diesel Vehicles.Starting a semi-truck is similar to starting a regular manual-transmission vehicle. First, ensure the transmission is set in neutral, depress the clutch pedal, and set the parking brake. Then, turn the key to start the engine. After starting, release the parking brake while keeping your foot on the brake pedal and the clutch pedal depressed. Next, select a gear gradually, release the clutch pedal, and you're ready to drive. The starting process resembles starting a standard automobile but on a larger scale.
-
QuestionWhat can I do if the truck will not start after filling it with diesel?Community AnswerMake sure there's no air in the system. With diesel trucks, you can not have any air running through the fuel lines. Crack and bleed it and pump on the fuel pump (located usually on the side of the engine or on top of the fuel filter, depending on the truck) and keep pumping that out until there are no longer air bubbles coming out through where you've cracked it and there's just fuel coming out. Tighten where you've cracked it and bled it from, and try again.
-
QuestionWhat are the different methods for starting a diesel engine?Community AnswerThere are several different options for starting diesels, and the best option for any particular engine depends on the design of the engine and any 'starting aids' it has. For a particular vehicle, your best option is to refer to the owner's manual for starting in various (hot/cold) conditions. If you have problems starting, it may be that the starting aids aren't working properly.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If your truck has been left in an extremely cold place, try to run the glow plugs more than once by turning the key to the start position, waiting for either the wait to start light or the glow plug light to go out, turning the truck off, and repeating the process.Thanks
- If you start your truck's engine without letting the glow plugs run, no engine damage will occur, but your truck may have a harder time starting.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Never use starting fluid on your diesel truck. Starting fluid is for gas engines only and (could harm your truck's pistons or combustion chamber.(If using starting fluid use with caution glow plugs and intake heaters will cause it to ignite early and blow the heads off.)Thanks
- Diesel fuel will turn into a gel at temperatures of below -6 to -18 degrees Celsius (21.2 to -.399 degrees Fahrenheit). The engine won't start because the fuel is frozen. If you are in an area with temperatures below these ranges, get your diesel fuel at a gas station that uses additives in the diesel that lower the freezing point of the fuel. The other option is to buy an additive at a truck stop in the area.Thanks
Advertisement
References
- ↑ https://youtu.be/Hf-Et-tR41Y?t=25
- ↑ https://www.dummies.com/home-garden/car-repair/diesel-engines/using-an-engine-heater-in-a-diesel-engine-for-cold-weather-starts/
- https://www.military.com/off-duty/autos/getting-diesel-engines-started-on-a-frosty-morning.html
- http://www.ford-trucks.com/forums/1045187-starting-a-diesel.html
- https://phys.org/news/2011-06-myths-diesel.html
About This Article
Thanks to all authors for creating a page that has been read 433,139 times.
Reader Success Stories
- "The article reminded me that diesel trucks start different than regular vehicles. Turn key partially, wait about 30 seconds, then fully turn key to start. Thanks." ..." more
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"The article reminded me that diesel trucks start different than regular vehicles. Turn key partially, wait about 30 seconds, then fully turn key to start. Thanks."
..."
more
"How the engine block heaters worked and the glow plugs helped."
