How to Inspect Car Radiator Hoses

Do a quick inspection and squeeze test to know if you need to replace your radiator hoses

Reviewed by Charley Helvy

Last Updated: March 6, 2024

The radiator is one of the most important devices in your car because it keeps the engine at its nominal operating temperature, which is typically between 195 and 220 degrees Fahrenheit (90 and 105 degrees Celsius). ^{[1]
X
Research source} Radiator hoses circulate coolant from the radiator to parts of the engine that need to stay cool; but over time, radiator hoses can weaken. If they are not replaced when necessary, they can completely collapse, causing the engine to overheat and unable to run. We'll walk you through how to check your radiator hoses, which may help you keep your engine from overheating.

Things You Should Know

Locate the upper radiator hose between the radiator and the motor. Find the lower hose beneath your car between the radiator and heat wall.
Check that the radiator hoses are neither cracked nor swollen.
Do a radiator hose squeeze test when the engine is still warm. Ideally, it will feel firm but not rock-hard.

Get Car Support Solve Any Problem

Hi there! Do you have a question about how to diagnose or fix a problem with your car? I’ve read the manual so you don’t have to. Select your make, model, and year, then ask away!

*

1

Find both of your radiator hoses.

Download Article

One reason radiator hoses are overlooked during a routine car inspection is that the hoses can be difficult to reach.
- The upper radiator hose runs from the radiator to the motor. You can usually see most of this hose.
- The lower radiator hose is harder to find. To locate it, get underneath the car and look for a smaller diameter hose leading from the radiator into the heat wall of the car.

2

Visually inspect each radiator hose.

Download Article

Hoses should not be swollen or cracked, both of which could lead to a failure. ^{[2]
X
Trustworthy Source
Consumer Reports
Nonprofit organization dedicated to consumer advocacy and product testing
Go to source}

3

Perform a squeeze test.

Download Article

While the engine is warm after a drive, squeeze the radiator hoses, paying particular attention to areas where the hose bends.
- A radiator hose in good condition should feel firm, but not hard.
- A radiator hose in poor condition feels very hard, spongy, or soft. You may find a single soft spot as opposed to the entire hose being soft. A soft hose or a hose with a soft spot should be replaced.

4

Check the clamps that connect the hose to the radiator and the engine.

Download Article

There are 3 different types of radiator hose connections, gear clamps, banded clamps, and wire clamps.
- Gear clamps, which are sometimes called worm clamps, and banded clamps, which are also called screw clamps, are typically made of stainless steel and wrap around the hose. You adjust these types of clamps with a screwdriver.
- Wire clamps are adjusted with a pair of hose clamp pliers. You can recognize these clamps because there is no screw keeping them tight.

Community Q&A

Search

Add New Question

Question

What can cause the top of the radiator hose to become swollen and the heat to no longer work?

Community Answer

The hose might have burst internally and if the coolant leaked or can't flow through properly, you could be running without enough coolant to run the heat. If so, you should replace the hose and replace your coolant.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 9 Helpful 10
Question

Why would the lower hose be cool, but the top hose hot?

Community Answer

Your thermostat controls coolant going to your lower hose. Either your engine has not reached sufficient temperature for the thermostat to operate, or your thermostat has gone bad and no longer operates properly. If your temperature gauge is past its normal point (about half way) and the bottom hose is still cold, fair chance your thermostat is bad.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 6
Question

Why is the top hose on my car very hard when it has been running for an hour or so?

Community Answer

This is perfectly normal. When your engine is at normal operating temperature, your cooling system is under pressure. The pressure in your system is limited by the radiator cap, usually around 15 psi. The hose feels hard because it is holding back the pressure in your cooling system. This is why you should periodically check the condition of the hoses.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 7 Helpful 12

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Hoses installed on a new car tend to last about 10 years or 100,000 miles (160,000 km). It is a good idea to do radiator hose inspection long before you reach these milestones.

Thanks
Helpful 0 Not Helpful 1
Clamps are very inexpensive. When you determine that it is time to replace a hose, replace the clamps that connect it to the radiator and engine at the same time.

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Never remove a hot radiator cap. Pressure built up inside the radiator can cause boiling coolant to gush out of the radiator, causing severe burns. ^{[3]
X
Research source}

Thanks
Helpful 0 Not Helpful 0

Things You'll Need

Flashlight (for inspecting the hoses underneath the engine)
Screwdriver (for tightening clamps, if necessary)
Hose clamp pliers (for adjusting wire clamps, if necessary)

[1]

[2]

Trustworthy Source

Go to source

[3]

Log in

How to Inspect Car Radiator Hoses

Things You Should Know

Steps

Get Car Support Solve Any Problem

Find both of your radiator hoses.

Visually inspect each radiator hose.

Perform a squeeze test.

Check the clamps that connect the hose to the radiator and the engine.

Community Q&A

Video

Tips

Warnings

Things You'll Need

You Might Also Like

References

About This Article

Reader Success Stories

Did this article help you?

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories