How to Install a Utility Sink

A comprehensive guide to installing the sink yourself

Co-authored by David Balkan

Last Updated: December 11, 2023

Utility sinks require a little bit of plumbing knowledge to install correctly. It’s recommended that you place the sink as close to a drain pipe as possible. The room’s drain pipe and vent pipe have to be sawn apart so you can connect them to the sink. You’ll also have to cut apart the water supply pipes and solder them back together to connect them to the faucet. Fasten on the rest of the sink’s plumbing and you’ll have a new sink where you need it.

Part 1

Part 1 of 3:

Connecting the Drain and Vent Pipes

Download Article

1
Turn the water supply valve to shut off the water supply. Locate the main water supply to the building. It’ll be where the water utility line enters your home, either inside or outside that room. It’s often near the water heating unit and has a red handle. Turn it clockwise to shut off the water.
- Always shut the valve that is closest to the inside plumbing, and don’t shut the valve that is closest to the street.
- If the room where the sink will be installed has supply valves, you can shut them off instead. They’ll be on the water pipes, but this isn’t always an option.
2
Cut through the drain pipe with a hacksaw . Locate the room’s drain pipe and pick where you’ll attach the sink’s pipes to it. It’ll run along the room near either the floor or ceiling, depending on where you’re installing the sink. Use a hacksaw to sever the pipe. ^{[1]
X
Research source}
- To figure out which pipe is which, consult the house’s blueprint or listen as water flows through the pipe. The drain pipe flows away from the building.
- If the pipe is overhead, such as in some basements, purchase a sink sump pump from the home improvement store.
Advertisement
3
Spread PVC cement over a wye fitting. First, go to a home improvement store and pick up a wye fitting. This piece of PVC pipe has a “Y” shape and is used to connect 3 pipes together. Brush PVC primer around the ends of the drain pipe to clean them. Then spread PVC cement inside the larger ends of the wye fitting.
- If your drain pipe is cast iron, it’s better to buy a rubber wye fitting and solder the pipes together instead of gluing them.
4
Slide the wye fitting over the drain pipe’s ends. Gently pull one end of the pipe to the side. Place the wye fitting on the pipe, then connect its other end to the remaining pipe. Hold the fitting in place for 4 seconds so the glue settles.
- The wye fitting should be positioned so the small, unattached opening faces towards where your sink will go.
5
Saw through the vent pipe. Look for a length of PVC pipe splitting from the drain pipe. It’ll go towards the ceiling and, if you follow it, to the roof. Pick a spot on the pipe above the wye fitting and near the ceiling. Use the hacksaw to sever the vent pipe.
- The vent pipe helps the sink drain and prevents sewer gas from entering the house.
Prime the vent pipe, then coat a 2nd wye fitting with PVC cement. Slide it onto the pipe parts to reconnect the vent. The small opening on the wye fitting should be angled downwards towards the other fitting.
7
Connect the wye fittings with PVC pipe. First, attach a T-shaped tee fitting to the lower wye fitting. Position it so the middle opening faces the higher wye fitting. Now connect the 2 by gluing together lengths of PVC pipe.
- If you’re using a sump pump, connect it to the vent and drain pipes according to the owner’s manual. ^{[2]
  X
  Research source}

Part 2

Part 2 of 3:

Setting up the Water Supply Lines

Download Article

Locate the pair of copper water supply lines in or on the room’s wall. One pipe carries cold water while the other carries hot water. Use your hacksaw to cleanly sever both lines.
Wear down the ends of the pipe with a 120-grit emery cloth. They’ll shine when you’re finished. Then, using a small flux brush, brush an even layer of flux over the shiny copper ends. ^{[3]
X
Research source}
Pick up a pair of copper tee fittings from the home improvement store. Brush flux inside the openings on both tee fittings, then slide the fittings onto the pipes. Leave the open end pointing outward towards where the sink will be placed.
Solder the copper pipes together with a propane torch. Hold some lead-free metal solder over one of the connecting joints. Turn on the torch and angle it so the end of the flame hits the solder. Move the torch from side to side to evenly heat the solder, melting it over the joint. Repeat this for the other joints on the pipes. ^{[4]
X
Research source}
5
Drill holes into the wall for wall anchors. Measure about a third of the way up the wall. Using a masonry bit, drill a hole in the wall behind each pipe. Keep the holes smaller than the width of the copper wall anchors.
- You may also use a hammer and nail to tap the holes into the wall.
Place the anchor’s screw in the pilot hole and hang the anchor on top of it. Then use a cordless screwdriver to tighten it against the wall. Gently guide the pipes into the anchor to secure them in place.

Part 3

Part 3 of 3:

Assembling the Sink’s Plumbing

Download Article

Set the sink in place to prepare for installation. Utility sinks are typically freestanding, so yours shouldn’t need extra fitting. Position the faucet openings near the wall. If the floor is uneven, adjust the screws on the sink’s legs until the sink appears level.
2
Secure the drain strainer in place with plumber’s putty. Roll some putty in your hands to warm it up. Wrap the putty around the underside of the strainer’s rim. Then push the strainer into the sink’s hole. Under the sink, turn the strainer’s nut clockwise with pliers to tighten it. ^{[5]
X
Research source}
- Wipe away any excess putty that oozes from the strainer.
First, use pliers to twist the nut on the P-trap counterclockwise. Remove the nut and the threaded flange, then slide them onto the sink’s tailpiece. Attach the tailpiece to the P-trap, then tighten the nut to hold it in place. ^{[6]
X
Research source}
You’ll need a pipe approximately 2 ¹ ⁄ ₂ in (6.4 cm) long. You may also need to glue on a few fittings to reach the drain. Slip some plastic, ring-shaped compression nuts over the pipes and tighten them with pliers. ^{[7]
X
Research source}
Spread the putty under the base of the faucet. Set the faucet in the hole on the sink’s rim and push it down to secure it. Wipe away any excess putty. Finish by sliding nuts onto the faucet from below the sink and tightening them.
You’ll need a pair of flexible, braided, stainless steel supply tubes. Connect a line to each of the tee fittings on the copper pipes. Twist the nuts with pliers to tighten the lines, then run the other ends through the faucet. ^{[8]
X
Research source}
Go back to the water supply valve and turn it on. Hot and cold water both should reach the sink. At last, your sink has running water!