Download Article
Download Article
Rushing a chair is one of the traditional methods of creating a seat for a chair with rails around the perimeter. Materials for rushing include twisted cattail leaves or even twisted strands of paper. The strands of rush are stretched across the seat and looped around the rails, moving in a counterclockwise direction, to fill in the seat. Pieces of corrugated cardboard are used for additional padding. Below, you will find information on how to rush a chair in this manner.
Steps
Download Article
-
Use a utility knife to remove the old rush seat. Do not to mar the frame of the chair. [1] X Research source- Remove any tacks with pliers.
-
Cut the rush into lengths of 30 feet (9.144 meters). The rush comes in a coil of 100 feet (30.48 meters) or more.Advertisement -
Dip each rush in a bucket of warm water for 12 seconds, and then shake off any excess water. -
Tack it to the inside left rail near the front leg (or slightly behind the last tack if you followed the tip for filling in a gap on a trapezoid-shaped seat). [2] X Research source -
Wrap it around the front rail and then the left rail so it is tight against the left front chair leg. [3] X Research source -
Pull it across the front of the seat. [4] X Research source -
Loop it around the right rail and then the front rail so it is tight against the right front chair leg. -
Take the strand to the back rail. Loop it around the back rail and then around the right rail so it is tight against the back right leg. -
Cross along the back rail and loop it around the left rail and then the back rail so it is tight against the back left leg. -
Bring it to the front rail and continue the sequence, moving counterclockwise around the seat, until you reach the end of the piece of rush. [5] X Research source- Knock the rushes tight against each other with a wooden block and hammer.
- Install temporary tacks through the last rush on all sides to help prevent them from slipping.
-
Tie another piece of rush to the end with a square knot and trim off the excess. The knot should be positioned under the seat so it is not visible. -
Insert corrugated cardboard as padding after weaving approximately 10 times around the perimeter of the seat.- Place a temporary tack holding the end of the last piece of rush.
- Cut pieces of cardboard into 4 triangles that are nearly as long as the side rails.
- Cut off the top corner of each triangle.
- Slip the side corners of each triangle into the woven rush near each leg.
-
Remove the temporary tack, tie on another piece of rush and continue in the same counterclockwise fashion over the cardboard until you completely cover the side rails with rush. -
Change the weaving pattern to a “figure 8” to fill in the rest of the front and back rails.- Place a temporary tack on the side rail and then thread the end of the rush up through the center opening of the seat. The temporary tack holds the woven part in place while you finish the seat.
- Pass the rush over the front rail, up through the center opening, over the back rail and up through the opening again. Repeat this figure-8 pattern until the front and back rails are filled in.
-
Hide the end of the rush by tacking it to the bottom of the front or back rail, and remove all temporary tacks.
Advertisement
Community Q&A
Search
-
QuestionWhat can I do with rush that is broken?Community AnswerThrow it away.
-
QuestionMy chair has armrests. I took out the screws, but the arms are loose. Should I thread the rush through the small opening, then put the screw back in the armrest?Community AnswerYes, but make sure you screw the arm back on properly.
-
QuestionWhere can I buy a rush chair?Community AnswerYou can buy a one time chair at Costco!
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Twist the fiber as you rush a chair to keep it wound and strong.Thanks
- Keep a constant pressure on the rush to make the seat strong and firm.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- If the seat of the chair does not have right angles at the front 2 corners, you will have to fill in the gap with short, individual strands. Do this by tacking it on the inside of the left rail, wrapping each one around the front and the left rails, crossing along the front rail and then wrapping it around the right and front rail. Tack it on the inside of the right rail.Thanks
Advertisement
Things You'll Need
- Utility knife
- Pliers
- Measuring tape
- Rush
- Pail of warm water
- Hammer
- Furniture tacks (Number 2 or 3)
- Block of wood
- Cardboard
References
- ↑ https://books.google.com.ph/books?id=YmYEAAAAMBAJ&pg=PP103&lpg=PP103&dq=removing+old+rush+seat+with+a+knife&source=bl&ots=710CvvuISj&sig=ACfU3U0qDC4PTmz-9UuYEnVnB3F1BHxktg&hl=en&sa=X&ved=2ahUKEwijz8rfm5bnAhVReXAKHUaYCVUQ6AEwFnoECAcQAQ#v=onepage&q=removing%20old%20rush%20seat%20with%20a%20knife&f=false
- ↑ https://www.youtube.com/watch?v=NQkE05DD9_Y&t=86s
- ↑ https://www.youtube.com/watch?v=AHu7lc5680w
- ↑ https://www.youtube.com/watch?v=ViClfS2tBAk
- ↑ https://www.youtube.com/watch?v=TuE1ujMQZpI
About This Article
Thanks to all authors for creating a page that has been read 84,287 times.
Reader Success Stories
- "I am encouraged to try to re-rush my chairs on my own now that I have this excellent guideline to follow."
Advertisement
91%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"I am encouraged to try to re-rush my chairs on my own now that I have this excellent guideline to follow."
"I'm printing this off to help me with rushing a chair. Also using YouTube to help me."
"The video and instructions were excellent!"
"Very helpful."
