PDF download Download Article PDF download Download Article

A closet is often the most under appreciated room in a house - until you need one. Then the storage space it represents becomes a valuable asset. It does not take a professional to build a closet only a willingness to set aside some time and have access to both hand tools and basic power tools.

  1. This can be the most difficult part of the process. The most logical place would be an alcove, the end of a hallway or on a wall without windows or doors to work around.
  2. Whether it is a wall or walk-in closet will depend on the amount of room available to you.
    Advertisement
  3. Be careful not to break the trim, since you will want to reuse it.
  4. Attach the base with deck screws to the floor and the top plate to the ceiling. Use 4-inch (10.2 cm) toggle bolts and construction adhesive.
    • Nail or screw the end studs to side walls and to the top and base plates and rough in the door opening by nailing the studs to the top and bottom plates. Studs traditionally are on 16 inches (40.8 cm) spacing. Just use the spacing you have if width of your wall is greater than 16 inches (40.8 cm) but less than 24 inches (61.2 cm). Split the difference for better support of the sheathing if the width is greater than 24 inches (61.2 cm).
    • Rough in the door framing. This will include trimmer studs on each side of the door. Dimensions are normally 6 feet (1.8 m), 10.5 inches (1.83 m x 26.7 cm) tall attached to the wall studs and a doubled 2 x 4-foot (5.1 X 10.2 cm) door header nailed to the door trimmer with the end nailed to the wall stud.
    • Place short studs (called cripples) between the door header and ceiling plate. This will normally be centered on 16 inches (40.8 cm). The framing is complete.
  5. Both sides of the framing use sheetrock screws. Cut sheetrock to size using a utility knife and a straight edge as a guide. Run the edge of sheathing to the roughed-in door openings.
    • Score the sheetrock with a utility knife. Begin breaking the sheetrock off with hand pressure and then with a straight edge (along the back side of the sheetrock). The sheetrock should snap off in one piece if it is scored deep enough.
  6. How to do this will depend on the type of doors chosen.
    • Insert the door into your rough opening if you are using a traditional prehung door (as for a walk-in-closet). Then, with a level, plumb the door using shims to keep it aligned. Install the trim supplied by the manufacturer around the door.
    • The use of a bi-fold door requires that you first trim out the door opening. Use trim similar to the floor trim you salvaged or that matches the trim in the room. Hang the door in place and adjust to fit, following manufacturer's instructions. [1]
    • Install the accessories, however elaborate or simple, that fit your needs.
  7. Advertisement


Community Q&A

Search
Add New Question
  • Question
    How do I install sliding doors?
    Community Answer
    Install according to manufacturer's instructions. They're usually easy to follow.
  • Question
    How do I expand my closet space?
    Community Answer
    Move the hanging rod up and then install another hanging rod below your clothes hanging on the top rod. You can also add shelves a few inches above the hanging rods to accommodate non-hanging items. Plastic totes are very good for placing on the floor. There are even shallow closet shelves that screw to the back or even front of the door.
  • Question
    How far between studs?
    Community Answer
    16" on-center or left edge to left edge. This translates to 14 1/2" actually between studs. However, if you know exactly where hanging rods will be going for 1 or 2-tier hanging then you may want a double stud there or blocking in between studs.
Ask a Question
      Advertisement

      Tips

      • Prehung doors are the easiest to install in that they come with all of the hardware installed and with the trim to go around the door. These are available at most home improvement stores. [2]
      • A good way to see how the space for the closet and the room fit together is to chalk out the closet walls, then place any needed furniture to see if it works.
      • Check to see the width and height requirements for the rough opening for the door you've chosen (when using prehung or bifold doors).
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • You will probably not need a building permit to install a closet. However, if you are adding electrical lighting or plugs, you may need an electrical permit which requires a licensed electrician to do the work. Check your local building codes.
      • Make sure that there are no existing electrical lines or plumbing in the way before installing or drilling into any existing walls. [3]
      Advertisement

      Things You'll Need

      • Framing hammer
      • Pry bar
      • Crosscut hand saw
      • Electrical miter saw
      • Power drill -- electrical or battery powered.
      • Utility knife
      • 4 foot (1.22 m) level
      • 4 inch (10.2 cm) x 1/4 inch (.5 cm) toggle bolts
      • 3 inch (7.6 cm) deck screws
      • 16 P framing nails
      • Construction adhesive
      • 2 x 4 inch x 8 foot (2.4 m) (5.1 x 10.2 cm x 2.44 m) Douglas fir or pine for framing
      • .5 inch x 8 foot (2.4 m) (1.3 cm x 2.44 m) sheetrock
      • 1.5 inch (3.8 cm) sheetrock screws or nails
      • Tape and embedment compound
      • 3 inch (7.62 cm) putty knife

      About This Article

      Thanks to all authors for creating a page that has been read 232,992 times.

      Reader Success Stories

      • Pat Moore

        Feb 26, 2017

        "The diagram with the written instruction was helpful. The visual enabled me to picture the space I will be building ..." more
      Share your story

      Did this article help you?

      Advertisement