Download Article
Learn how to hard reset a number of Honeywell thermostat models
Download Article
Have you tried to reset your Honeywell thermostat, but you've discovered your device has no reset button? Thankfully, not all hope is lost. For Honeywell thermostat models without a reset button, you can either find the reset option in the on-screen menus, or you can remove it from the wall and take out the batteries. Keep reading to learn more.
Ways to Reset a Honeywell Thermostat
- In some models, all you need to do is press the Menu button and choose the reset option.
- In other models, you'll need to do a series of button presses to get the reset option.
- A couple of models require you to change numbers on the screen to reset the thermostat.
- If your thermostat is battery-operated, remove the batteries and put them back in.
Steps
Section 1 of 9:
T9
-
Press the menu button on the screen. It's at the bottom of the screen and has an icon of three horizontal lines.
-
Select Advanced Setup . You'll have to scroll to find this option.Advertisement
-
Choose Reset > Factory Reset . Your thermostat will immediately begin to reset. This may take a few moments to complete.EXPERT TIPAir Conditioning SpecialistVictor Belavus is an Air Conditioning Specialist and the Owner of 212 HVAC, an air condition repair and installation company based in Brooklyn, New York. In addition to HVAC and air conditioning units, Victor also specializes in furnace repair and air duct cleaning. He has over 10 years of experience working with HVAC systems.
Remember to re-program your thermostat's schedule after resetting it. Resetting your thermostat will clear out any schedules you had created for the device. Be sure to set those schedules again by choosing the Schedule or Program option on your thermostat.
Advertisement
Section 2 of 9:
T10
-
Press the menu button on the screen. It's located at the bottom of the screen, and has an icon of three horizontal lines.
-
Select Thermostat Information . Take note of the date code, which is a four-digit number.
- After writing down the date code, press the back arrow button.
-
Press Installer Options . When prompted, enter the date code as the password.
-
Press Reset > Factory Reset . Your thermostat will immediately begin to reset. This may take a few moments to complete.
Advertisement
Section 3 of 9:
T5+/T5/T6
Section 4 of 9:
Smart/Lyric Round
Section 5 of 9:
Smart WiFi 9000
-
Press the Menu button. This button is in the upper-right corner. It may say Settings instead of Menu .
-
Choose Preferences . You'll need to scroll to find this option.
-
Select Restore Factory Defaults > Yes . Your thermostat will immediately begin to reset. This may take a few moments to complete.
Advertisement
Section 6 of 9:
FocusPro 6000
-
Press the up arrow button and the fan button at the same time. You'll need to press and hold these buttons for a few seconds until you see the screen change.
-
Adjust the left number to 90 and the right number to 1. Use the buttons on the front of the thermostat to adjust the numbers.
-
Press Done . Your thermostat will immediately begin to reset. This may take a few moments to complete. [1] X Research source
Advertisement
Section 7 of 9:
VisionPRO 8000
-
Press System . It's a button located at the top of the screen.
-
Press and hold the blank box. It's located in the center of the screen.
-
Adjust the numbers. Change the number on the left to 0710 and the number on the right to 1 .
-
Press Done . Your thermostat will immediately begin to reset. This may take a few moments to complete.
Advertisement
Section 8 of 9:
VisionPRO TH8321WF
-
Press System . It's a button located at the top of the screen.
-
Select Dealer Information . Take note of the date code, which is a four-digit number.
- After writing down the date code, press the back arrow button.
-
Press Installer Options . When prompted, enter the date code as the password.
-
Press Reset > Factory Reset . Your thermostat will immediately begin to reset. This may take a few moments to complete.
Advertisement
Section 9 of 9:
Battery-Powered Thermostats
-
Remove the thermostat from the wall. To remove the thermostat from the wall, pull it away from the wall gently but firmly. [2] X Research source
-
Remove the batteries from the back of the thermostat. If your thermostat can be powered down, make sure to do so before removing the batteries.
-
Place the batteries in the thermostat in the wrong direction. Leave the batteries like this for at least 10 seconds.
-
Put the batteries back in the thermostat correctly. Power on the thermostat, if required, and hang it back on the wall. The thermostat will be reset back to factory settings.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If your Honeywell thermostat isn't working properly and it's over ten years old, a reset may not solve your problems, according to Victor Belavus, air conditioning specialist. "If your thermostat is over ten years old, it might be time to replace it, as older thermostats may not be as accurate or efficient."Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
About This Article
Thanks to all authors for creating a page that has been read 206 times.
Advertisement