Download Article
Download Article
A grease gun can be a handy tool for the home mechanic because car parts often need to be greased to reduce friction and increase the life of the part. A grease gun can inject grease into areas that are difficult to reach. Using a grease gun can be easy once you have taken it apart and loaded it. By doing this, you immediately see how the gun works and you are ready to use it with no further directions.
Steps
-
Remove the head of the gun from its barrel. -
Pull the rod handle back. [1] X Research sourceAdvertisement -
Lock the rod handle. -
Open the new grease cartridge. -
Insert the new grease cartridge into the barrel of the gun. -
Note the pull-tag on the end of the new cartridge. -
Ensure that cartridge is pushed in enough so that the rim is in contact with the rim of the grease gun. -
Reinstall the barrel to the end cap but keep it loose. -
Release the rod handle by turning it out from the retaining groove in the end cap. -
Depress the rod handle; this will force grease into the head of the grease gun and force air out. -
Pump some grease through the nozzle and wipe it clean before attaching the nozzle to the gun. -
Tighten the cap and push down on the air bleeder to force out the rest of the air. -
Place the grease gun coupler at the end of the extension hose directly on the area to be greased. -
Pump the lever handle enough times for grease to begin flowing.
Advertisement
-
Remove the head from the barrel as above. [2] X Research source -
Put a large amount of grease in the head and pack firmly. -
Position the barrel of the gun over a tub of grease. -
Insert the barrel down about 2 inches (5.1 cm) into the grease. -
Push down on the barrel while pulling up on the plunger or rod handle. -
Lock the rod handle when it is fully extended. -
Move the gun barrel from side to side to cut off the extra grease after the barrel is full. -
Clean off all parts with stiff paper, paper towel or rag. -
Attach the gun barrel to the rest of the unit. -
Unlock the rod handle. -
Pump the grease gun handle to start the flow of grease. -
Place the grease gun coupler at the end of the extension hose directly on the area to be greased.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- If there is no air relief valve on your grease gun, do not tighten the head completely and push the rod handle several times to prime the gun. You can then tighten the head and proceed.Thanks
- The first time you use your grease gun, create a seal around the rubber plunger assembly by applying a layer of grease around it before inserting it into the gun barrel.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- All nozzles, nipples and needles should be cleaned before use to prevent clogs.Thanks
- It is important that the grease being loaded into the grease gun is free of any contaminants, such as lint, dust or metal shavings.Thanks
- Grease guns come equipped with several parts such as nipples and needles to get grease into small openings. Caution should be taken when using these attachments, especially the needles, because they can slip and puncture your skin. If grease gets into your skin, it can cause some severe medical problems, such as infections and even gangrene.Thanks
- Before storing your grease gun, release the air pressure. Store horizontally away from heat and moisture. [3] X Research sourceThanks
Advertisement
Things You'll Need
- Manual grease gun
- Grease cartridge or tub
- Gloves
- Paper towels
- Stiff paper, cardboard or rags
- Protective clothing
References
About This Article
Article Summary
X
To use a grease gun, start by pulling back the rod handle and placing a grease cartridge into the gun. Make sure the rim of the cartridge is in contact with the rim of the gun before returning the rod handle to its original position. Then, depress the rod handle to force grease into the head of the gun, which will push the air out. Next, attach the nozzle and connect the gun to the extension hose. Once you're ready, pump the lever handle until the grease begins flowing. For tips on how to load a grease gun from a tub of grease, keep reading!
Did this summary help you?
Thanks to all authors for creating a page that has been read 124,251 times.
Reader Success Stories
- "Just bought a new manual grease pump and did not know how to use it. But after reading wikiHow, I can now use it comfortably. Thank you." ..." more
Advertisement
91%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"Just bought a new manual grease pump and did not know how to use it. But after reading wikiHow, I can now use it comfortably. Thank you."
..."
more
