Download Article
Download Article
If your iPhone charger is acting up, the tip might have gotten dirty or corroded. Luckily, with a few household items, it is possible to clean the connectors on your charger and potentially get it working again. This wikiHow article will teach you how to remove buildup on the tip of your iPhone charger.
iPhone Charging Cable Cleaning Tips
There are two ways to clean a dirty iPhone charger: rubbing alcohol or a baking soda/vinegar solution. Dip a q-tip in the cleaning solution of your choice, and rub it on the iPhone charger. If there's some stuck on grime, scrape it off with a toothpick. Make sure to let your charger dry before using it again.
Steps
-
Gather a q-tip, rubbing alcohol, a toothpick, a towel, and your charger. You might already have these items around the house, but if not, they can likely all be found at your local grocery store.
-
Dip the end of the q-tip in rubbing alcohol. [1] X Expert Source Linh Le
Certified Mobile Repair Specialist Expert Interview. 10 February 2022. Use the rubbing alcohol with the highest alcohol percentage you can find. Ideally, it would be 99%. [2] X Research source- Lower alcohol percentages mean there is more water in the solution, which can corrode your charger.
Advertisement -
Rub the charger tip with the q-tip. When cleaning the tip of the charger, do not be afraid to apply some pressure.- Often, chargers that fail due to corrosion have a visibly dirty fifth gold pin (when viewed with the metal tip below the white insulation). This is the most powerful circuit, so be sure to clean it as well as you can.
-
Scrape the charger tip with the toothpick. After using the q-tip, some spots may remain on the tip of your charger. Use a toothpick to remove any residue or corrosion while being careful of the gold connectors.
- If you damage a gold connector, the charger will stop working permanently, so do not scrape too hard!
-
Dry the charger. After drying the charger with your towel, wait as long as it takes to ensure there is no remaining liquid.
-
Plug the charger into your phone. If your phone begins charging, you have successfully cleaned your charger! Otherwise, if the charger still is not working, and the tip is still corroded, try cleaning it once more.
Advertisement
-
Gather three q-tips, water, baking soda, liquid soap, white vinegar or lemon juice, a toothpick, a towel, and your charger. These are relatively common household items, but if you cannot find any of them, they are almost certainly available at your local grocery store.
-
De-grease the charger tip with soap and water. Dip your q-tip in some warm water with a little bit of soap, then rub the charger tip gently on each side. This will remove any residual grease from your hands. [3] X Research source
- If you are not sure what soap to use, dishwashing detergent or hand soap will work!
-
Mix water, baking soda, and white vinegar or lemon juice. You can measure out about half a cup of water, a teaspoon of baking soda, and a teaspoon of white vinegar or lemon juice. Warm water is preferable, but if you only have cold water, that is ok.
-
Scrub the charger tip with the baking soda solution. Dip your second q-tip in the solution you just made, then clean the lightning connector. Do not be afraid to apply pressure and clean it for several minutes, as this is necessary to remove the tougher build-up.
- Chargers that stop working due to corrosion often have a significant amount of buildup on the fifth gold pin (when viewed with the metal tip below the white insulation). This is the most powerful circuit, so be sure to clean it as well as you can.
-
Remove residue and corrosion with the toothpick. For especially resistant spots, lightly clean the charger tip with a toothpick. Be careful not to damage the gold pins, or your charger will stop working permanently!
-
Clean the charger tip with water. Dip your last q-tip in warm water and rub both sides of the connector once more to remove the baking soda solution.
- Do not clean your charger tip with running water! If there is a leak in the cable connector housing, it will ruin the charger.
-
Dry the charger. Pat the connector dry with a towel, then wait two to three minutes to ensure it is completely dry.
-
Plug the charger into your phone. If your phone starts charging, the cleaning worked! Otherwise, if you can still see corrosion on the charger, try cleaning it once more.
Advertisement
Expert Q&A
Search
-
QuestionHow can I clean my iPhone charger port without a toothpick?Linh Le is a Certified Mobile Repair Specialist and the Owner of SC Mobile Repairs in San Clemente, California. With more than 12 years of experience, he specializes in smartphone, tablet, and smartwatch hardware repair. Linh has an iTech Mobile Device Repair Certification and an iOS Certification. He holds a Bachelor’s degree from The Franciscan University of Steubenville.Go over the charger port with a small, square alcohol wipe—those work really well!
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- When cleaning the charger tip, try to avoid bending the wires in the charger too much. Otherwise, they can eventually break or disconnect from the housing of the connector.Thanks
- If you have tried other chargers and they do not work or corrode quickly, the problem may be the charging port on your phone. Try cleaning the charging port as shown in the linked article and contacting Apple for repairs.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
- ↑ Linh Le. Certified Mobile Repair Specialist. Expert Interview. 10 February 2022.
- ↑ https://www.youtube.com/watch?v=7FLMCzv94fI
- ↑ https://www.thetechmentor.com/posts/clean-iphone-cable-port-intermittent-charging/
About This Article
Thanks to all authors for creating a page that has been read 76,723 times.
Advertisement
