Download Article
Download Article
A Tech-Deck is one of the hottest collectible toys out there today. They come with a 96-mm board complete with trucks, bearings, grip tape and authentic kick-butt graphics you see on real skateboards - which are all of different brands. These include Blind, Plan B, World Industries and many more. They also come with a Skate Tool for changing the wheels, stickers to add to your boards (or skateparks if you have them) and extra graphic wheels. If you are still not satisfied with all they give you, maybe it's time to customize your board! Maybe you just want it to be a little bit more colourful, maybe you want the kicks higher so you can do Kickflips and Ollies etc. higher. Or maybe you want to create your own graphic! The possibilities are endless, but a few are packed into this article.
Steps
-
Grab a black and PERMANENT marker, Sharpies are great and dry fast but any permanent marker should do. -
Locate the Tech Deck logo on the grip tape and start dotting away at it with the permanent marker.Advertisement -
Do NOT colour, just dot it, it looks a lot better and doesn't wreck your permanent marker. -
Do this until you can't see the Tech Deck logo anymore. -
You can also cut a line in the grip tape, but there are two ways: The hard way and the easy way, but doing it the hard way improves the result.
Advertisement
-
Grab scissors or a sharp knife and -
Locate the two pairs of bolts on any end of the board (They are on the two ends of the grip tape) -
Look about half an inch closer to the middle of the board. -
Do slow, but sure vertical cuts on this area. The cut should be about a third of the width of your fingernail - approx. 5 mm in width. -
Make sure you cut the whole area vertically, as in no grip tape left in that 5 mm width of area. This looks pretty awesome and, if you wish, you can then colour the line with different coloured permanent markers, and then even go on to the rim of the deck!
Advertisement
-
Take the grip tape off the deck but without ripping it. An easy way to do this is to soak the board in hot water for about 5 min. This burns out some of the glue holding the grip tape to the board. -
Try to get your fingernail under the board and just very, very carefully, pull away. -
Take your time when you do this, just don't rip the board. Once the grip tape is off, cut two parts of the grip tape off in the same area as shown in the previous section. The two parts cut should be the same width as the line should be - namely, about 5 mm apart. -
Superglue the two pieces back to the deck, with both of the ends covered in grip tape, so the line is in the right place. -
Put the board in the freezer for sometime, so the glue hardens and therefore sticks the grip tape better. About 15 minutes should do, but 20 to 30 minutes is good if you really want to make it perfect. Done!
Advertisement
-
Grab sandpaper and use it to scratch the graphic off the bottom of the board. If you take the trucks and wheels off the board, this will be much easier as they take up room so it will be harder to get to those parts of the graphic. -
Grab permanent markers of different colours and make up your own graphic! Some ideas are polka dots, stripes, fireworks or just a whole one colour altogether - for example you could make a full-on purple board! -
Colour the whole bottom purple, the whole side purple, dot out the logo with a black marker, perhaps even cut a line on the grip tape and colour it purple! The only limit is your imagination.
Advertisement
-
Soak the board in hot water for at least 20 minutes (30 is better, but 20 would do). -
Bend the kicks up, try to do it not too wildly (especially the first time, as taking away pop isn't easy), otherwise it would look very fake and you could just do cheating Ollies, so just bend a little. -
Soak in cold water or put it in the freezer, for 15 to 20 min. -
You could also use a hairdryer and use it to heat up the deck.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Also try changing the wheels and adding stickers.Thanks
- To change the trucks, put the smaller end of the skate tool in the screws on the top of the deck and twist left. Do this for all of them. To put a truck into the deck, hold the truck where it would go while putting screws in and twisting right until you can't twist any further.Thanks
- If you wanted to change the wheels, take the Skate Tool and put the wider end in the wheel. Twist left - remember, "Righty tighty, lefty Lucy(loosey)", until the wheel comes out along with the nut. To put a wheel in, put the nut in the tool upright and put a wheel in the truck. Insert the tool and twist to the right until it's reasonably tight.Thanks
Tips from our Readers
The advice in this section is based on the lived experiences of wikiHow readers like you. If you have a helpful tip you’d like to share on wikiHow, please submit it in the field below.
- For a smoother feel, get bearing wheels for your fingerboard. Instead of being plastic wheels on metal trucks, it will be metal wheels on metal trucks, and they feel exceptionally smoother.
- You can just place the tech deck in the water for 5 minutes, then gently peel the grip tape off.
- If you want better pop and a nice, crispy feel, consider getting foam griptape.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Once you've done these things, you won't be able to undo it - except for the grip tape, you can just get new grip tape and stick it on.Thanks
Advertisement
Things You'll Need
- Tech Deck
- Sharpies/ Permanent markers and/or different coloured ones
- Scissors or knife
- Access to hot water and/or hot water
- Hairdryer
- Superglue
- Skate tool
- Sandpaper
- Freezer
About This Article
Thanks to all authors for creating a page that has been read 68,232 times.
Advertisement
