How to Fix Gas Water Heater After a Flood

PDF download Download Article
PDF download Download Article

Coming home to find your basement flooded with water is bad enough, but realizing that your water heater is also broken is even worse. But don't worry, this article will teach you how to fix a gas water heater after a flood.

Steps

PDF download Download Article
  1. This is usually done with a submersible pump. [1]
  2. This will prevent a leak in the event a control valve is damaged by water. [2]
    Advertisement
  3. Every water heater is a bit different. you may be able to get by with a small adjustable wrench, channel locks, air compressor, blowgun, and rags.
  4. Thermocouples come in both right and left thread. [3] Be careful to turn yours in the right direction as excessive tightening can damage the control.
  5. The burner assembly should now pull out of the chamber.
  6. Replace the entire burner assembly if damaged. Otherwise, clean the burner assembly with rags and blow out all orifices with air hose.
  8. Replace the burner assembly in the burner chamber ensuring that locating features are aligned and clips are replaced (if applicable). This hold the burner in the center of the chamber.
  10. (Do Not over-tighten --- brass fittings strip easily)
  12. Turn gas supply on at valve and spray leak detector on all fittings. If you do not have leak detector use water and dish soap mixed at about 75% 25% respectively. Leaks will present by creating bubbles around fittings. [4]
  13. Usually a good teflon tape sealant does the trick.
  14. The gas water heater should be ready to go.
    15. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What's wrong if the pilot light will light, but when I turn on the heater it goes out?
    Community Answer
    Most likely it is due to a bad thermocouple, you'll need to replace it. It is a very cheap part to replace.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 3 Helpful 6
  • Question
    Can I use paper to start a water heater with an igniter, and bypass using the igniter?
    Community Answer
    No. The system is designed to not work at all if any component fails a checksum.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 0 Helpful 4
  • Question
    How do I clean the gas valve on a hot water heater?
    Community Answer
    Replace it. It's not a serviceable part, and should never be tampered with.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 7 Helpful 3
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • clean out the PILOT TUBE and PILOT ORIFICE even after suspecting the thermocouple (copper tube).
        Thanks
        Helpful 0 Not Helpful 0
      • clean your observation window and use your smartphone camera or mirror for a better view of the pilot light.
        Thanks
        Helpful 1 Not Helpful 0
      • add a comfortable 3/4" rubber floor mat or rug to work on for this repair.
        Thanks
        Helpful 1 Not Helpful 0
      Show More Tips
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      • Never service a gas appliance with gas line connected. Always disconnect gas lines before servicing. Clear the work area of any possible ignition sources.
        Thanks
        Helpful 3 Not Helpful 3


      Advertisement

      You Might Also Like

      How to
      Survive a Nuclear Attack
      How to
      Build an Underground Bunker
      How to
      Build a Fallout Shelter
      How to
      Escape from a Sinking Car
      How to
      Survive a War
      How to
      Survive an Apocalypse
      How to
      Survive an EMP
      How to
      Survive a Plane Crash
      How to
      Boil Water Without Electricity or Gas
      How to
      Survive an Abduction or Hostage Situation
      What to Do If You Get Stuck in an Elevator
      How to
      Survive a School or Workplace Shooting
      How to
      Prepare for Nuclear War
      How to
      Make a Safe Room for Your House
      Advertisement

      References

      1. ↑ https://www.popularmechanics.com/home/interior-projects/how-to/a6414/fix-a-flooded-basement/
      2. ↑ https://inspectapedia.com/heat/Flood-Damaged-Water-Heater-Repair.php
      3. ↑ https://inspectapedia.com/heat/Flood-Damaged-Water-Heater-Repair.php
      4. ↑ https://www.dummies.com/home-garden/home-improvement/kitchen-bath-remodeling/how-to-check-for-gas-line-leaks/

      About This Article

      Thanks to all authors for creating a page that has been read 158,737 times.

      Did this article help you?

      Advertisement