How to Install Surface Mount Hinges

PDF download Download Article
PDF download Download Article

Surface mount hinges are hinges that attach right to the surface of your project, as opposed to hinges that require you to recess the surface in order to attach them. You can use surface mount hinges to install doors, cabinets, or other pieces that need to be attached with a hinge. Installing them is easy and won't take long!

Part 1
Part 1 of 2:

Aligning the Hinges

PDF download Download Article
  1. Some hinges are all one piece and can’t be taken apart. However, if your hinge can be separated into pieces, remove the hinge pin to take the hinge apart. This will help you install it easier.
    • The package your hinges come in should tell you whether or not they can be taken apart.
  2. Measure your cabinet or door so you can space the hinges the same distance from each end. Use a level or combination square to make sure the hinge is even. [1] Mark the spot where you’d like the hinge to go using a pencil or piece of painter’s tape. If you’ve taken the hinge apart, remember to mark the spots for the 2 pieces, not just 1.
    • A door hinge is usually installed 5 inches (13 cm) from the top of the door and 10 inches (25 cm) from the bottom.
    • To use a level, set the level at the top of the hinge. Rotate the hinge until the bubble in the level is between the 2 middle vertical lines.
    • Use a combination square by lining up the edge of the square with the edge of the door, cabinet, etc. The combination square will create a right angle, helping you line up your hinge.
    Advertisement
  3. Once you’ve decided where the 2 hinge pieces will be placed, trace around the hinge and screw holes using a pencil. Remove the entire hinge once you’ve traced it. [2]
  4. Use a center punch to mark the center of each hole that you just traced. If you don’t have a center punch, you can use a nail and hammer to create a small hole exactly where you’d like the screws to go.
    • Place the tip of the center punch on the center of the hole—you can use a pencil or pen to mark the center. Use a hammer to hit the top of the center punch, creating the indentation.
    5. Advertisement
Part 2
Part 2 of 2:

Attaching the Hinges

PDF download Download Article
  1. [3] Place your drill bit into the indentations left from the center punch—these will help keep your drill from moving around. Carefully drill the holes for all of the screws.
    • Use a drill bit that’s slightly smaller than your screw size.
    • You can look up charts online that will tell you what size drill bit to use according to your screw size.
    • Do a visual check by holding up the drill bit in front of the screw. If you can't see the threads of the screw, the drill bit is too big and you need to go down a size or 2.
  2. Line up the hinges so that they're in the center of their tracings, then place a screw in each hole so you can tighten them down.
  3. Use a screwdriver to begin tightening each screw 1 at a time. Tighten the first screw 3 rotations, and then move on to the next screw. Do this until they’re all evenly tightened. [4]
  4. If your hinge came in 2 pieces with a hinge pin, you can replace it once the screws are nice and tight. Just drop it into place in between the 2 hinge pieces.
    • If you’re installing a door or cabinet, put the top hinge in first to help with the alignment.
    5. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • You can find reversible hinges as well as left and right hand hinges. Make sure you have the proper type of hinge for your project. [5]
        Thanks
        Helpful 0 Not Helpful 1
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Things You'll Need

      • Hinges
      • Measuring tape
      • Pencil or pen
      • Center punch
      • Hammer
      • Drill
      • Screws
      • Screwdriver
      • Level (optional)
      • Combination square (optional)

      You Might Also Like

      How to
      Adjust Soft Close Hinges
      How to
      Adjust Door Hinges
      How to
      Remove a Door Hinge Pin
      How to
      Lubricate Door Hinges
      How to
      Fix a Stripped Screw Hole in a Door Hinge
      How to
      Stop Squeaky Door Hinges
      How to
      Adjust & Reposition Euro-Style Cabinet Hinges
      How to
      Install New Cabinet Hinges for Your Kitchen or Bathroom
      How to
      Apply WD‐40 to Door Hinges
      How to
      Clean Cabinet Hinges
      Advertisement

      References

      1. ↑ Jason Phillip. Handyman. Expert Interview. 2 July 2020.
      2. ↑ https://www.youtube.com/watch?v=0aSF3oiKY9g </ref#t=27s
      3. ↑ Jason Phillip. Handyman. Expert Interview. 2 July 2020.
      4. ↑ https://www.youtube.com/watch?v=0aSF3oiKY9g#t=1m50s
      5. ↑ http://www.dulley.com/diy/dw105.htm

      About This Article

      Thanks to all authors for creating a page that has been read 52,321 times.

      Did this article help you?

      Advertisement