Download Article
Retrofit your home to stay warm in winter and keep cool in the summer
Download Article
Even the nicest of living spaces can be a little unpleasant if your walls aren’t insulated enough. But what can you do if your home is already finished and the drywall is up? A lot, actually—you have tons of choices here! In this article, we’ll explain how you can do this on your own or hire someone to do it for you. We’ll also cover some key questions and considerations you likely have if you’re considering insulating a finished wall.
Things You Should Know
- Install injectable insulation foam by drilling holes in your drywall and spraying the expandable foam inside.
- You can also hire a contractor to install blanket or cellulose insulation inside finished walls.
- If you’re only insulating a room or two, it’s probably more efficient to remove the drywall and use standard spray foam.
Steps
Section 1 of 4:
Spray Foam DIY Insulation
-
Choose an injection foam spray kit that meets your needs. Injection foam insulation expands inside of the wall to insulate it. This process is known as “drill and fill” retrofitting, and it’s basically your only option so far as DIY insulation options go. These kits contain everything you need to install the foam itself. Reach out to a manufacturer to schedule a delivery. [1] X Research source
- One of the most popular options out there is the Tiger Foam spray kit.
- As a note, you 100% have to use “injection foam.” The normal polyurethane foam that doesn’t expand can not be applied to finished walls. [2] X Research source
- DAP offers a Touch ‘n’ Foam kit you can pick up at Home Depot. You’ll need to buy a respirator , a disposable suit , and nitrile gloves separately.
-
Take a thermal image of the walls to spot studs and wires. Buy or rent a thermal camera and use it to scan your walls. The cold spots (or hot spots, if it’s summer) represent the gaps in your wall. You must not drill into any wires, studs, or receptacles, and you’ll get the best insulation by drilling into the center of each wall section. [3] X Research source
- Refer to the thermal imaging regularly when you’re drilling the holes into the wall.
- The studs, which should sit every 16–24 inches (41–61 cm) in the wall, create closed off pockets in the wall. By applying expandable insulation foam to the center of each section, the foam will spread out evenly through the wall.
- You can use a stud finder if you don’t want to rent or buy a thermal camera, but it’s a lot more time consuming. It’s also riskier, since a stud finder may not catch electrical lines or pipes.
Advertisement -
Drill holes into each section of the wall using a hole saw. Grab a hole saw that matches the size of the nozzle on your spray kit and attach it to your drill. Use your camera and a measuring tape to locate the center of each internal pocket in the walls. Then, drive a hole into the center of each section that you want to insulate. [4] X Research source
- The final result should look like a series of evenly-spaced holes, all at the same height on the walls.
- This process can also be completed from the exterior by removing the siding or drilling through the exterior. However, this is especially difficult for a non-contractor to do since you can’t rely on the thermal imaging.
-
Put on your safety gear and blow the insulation into the holes. Put on your disposable suit, respirator, and gloves. Follow the manufacturer’s directions to hook up the insulation tanks. Insert the nozzle into the wall. Pull the trigger to begin filling the wall. Angle the nozzle downwards then point it upwards as soon as you see the foam reaching your height. [5] X Research source
- You are not going to perfectly fill each cavity perfectly. Don’t keep spraying once the foam starts pushing back on your nozzle.
- Use your thermal camera to see if you’re adequately filling up the cavities.
- If you feel pressure coming back on the nozzle or the drywall starts bulging or buckling, stop. If you fill the wall with too much foam and it has nowhere to go, it can damage the joists, studs, or drywall.
-
Plug the holes and paint over them to repair the walls. Once you’ve filled each section of your wall, scrape or wipe away any spray foam that sticks out from the holes. Then, wait for the foam to cure and harden (this can take up to 60 minutes). Once it has cured, patch the drywall with spackle. Wait 24 hours and sand the dried spackle before painting it to match the rest of your home. [6] X Research source
- You may need to apply multiple layers of paint to ensure that the repairs blend in.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Expert Interview
Thanks for reading our article! If you'd like to learn more about insulating a wall, check out our in-depth interview with Ryaan Tuttle .
References
- ↑ https://basc.pnnl.gov/resource-guides/blown-insulation-cavities-existing-exterior-walls
- ↑ https://youtu.be/_dOm0a4unEw?t=39
- ↑ https://basc.pnnl.gov/resource-guides/blown-insulation-cavities-existing-exterior-walls
- ↑ https://ccrpc.org/wp-content/uploads/2018/12/IHWAP-Field-Standards-Manual-2018.pdf
- ↑ https://ccrpc.org/wp-content/uploads/2018/12/IHWAP-Field-Standards-Manual-2018.pdf
- ↑ https://www.spraypolyurethane.org/do-it-yourselfer/frequently-asked-questions/
- ↑ https://www.energy.gov/energysaver/types-insulation
- ↑ https://www.energy.gov/energysaver/types-insulation
- ↑ https://www.energy.gov/energysaver/where-insulate-home
About This Article
Thanks to all authors for creating a page that has been read 24,669 times.
Advertisement