Download Article
Download Article
Did you know that cloudy, roughed-up acrylic can be sanded down to a shine? If you didn’t, you’re in for a treat. Polished acrylic looks crisp, shiny, and smooth. You can even flame-polish your acrylic to give it a texture resembling glass. In this article, we’ll walk you through both options so that you can choose the solution that makes sense to you. Read on to learn how to polish your acrylic.
Steps
-
Cut out a piece of 180-grit sandpaper. Place a sanding block in the corner of a sheet of sandpaper and trace an outline around the block with a pencil. Add an extra 0.5 inches (1.3 cm) to the bottom of the outline so you can place that bit of sandpaper into the sanding block. Then, take a utility knife and cut along the outline. [1] X Research source
- You will have to repeat this process for the 320-360 and 600-grit sandpaper.
-
Attach the 180-grit sandpaper to the sanding block. Open the bottom of the sanding block to create a gap where the extra sandpaper goes and slide the paper in. The sandpaper should fit tightly on the block, meaning there shouldn't be any airspace between the paper and the sanding block.
- The coarse side of the sandpaper should be facing away from the sanding block.
- You can pick up a foam or rubber sanding block at your local hardware store or order one online.
Advertisement -
Spray the edges of the acrylic with a spray bottle. Use lukewarm water and spray evenly, making sure to wet every part of the acrylic piece. Make sure to re-spray the acrylic as you switch sandpapers. [2] X Research source
- Wet-sanding is what allows you to polish the acrylic and make it look shiny and new. If you forget to use water, you could damage the acrylic and make it unusable.
-
Smooth the edges of the acrylic with 180-grit sandpaper. Vigorously rub the sandpaper into the acrylic to straighten out the edges and smooth the material. This sets the table for the higher-grit sandpapers to polish up the acrylic and give it that shine you're looking for. [3] X Research source
- To get a feel for sanding acrylic, practice on extra scraps that are left over from your project.
-
Change to 320-360-grit sandpaper to get a polished finish. Once you've cut out pieces of finer sandpaper and attached them to the sanding block, wet-sand the edges of the acrylic to finish the job properly. When the acrylic starts to have a greater shine to it, you know the 320-360-grit sandpaper has done its job. If you keep sanding and don't see the acrylic get shinier, that's when it's time to move on to a higher grit of sandpaper. [4] X Research source
- Take breaks in between sanding so your hand doesn't cramp.
-
Finish sanding with 600-grit paper to give the acrylic a lasting shine. Using a higher grit of sandpaper will make the acrylic shine even more than it already did. Sanding acrylic takes time, so don't get frustrated if the material doesn't get polished right away. [5] X Research source
- The higher the grit of the sandpaper, the finer it is.
Advertisement
-
Purchase a propane torch to give the acrylic a glass-like finish. You can pick up a torch at your local hardware or home improvement store. You can also order a torch online. Propane torches are not ridiculously expensive and have many other uses around the house. You can get a good propane torch for fewer than 50 dollars. [6] X Research source
- Other uses for the torch include melting snow and ice on outdoor staircases and walkways, starting fires, and removing old sealant on windows.
-
Practice using a propane torch on left over acrylic scraps. There are bound to be some extra pieces of acrylic lying around no matter what you're using the material for, so put the left-over pieces to good use by trying out the propane torch on them. This allows you to get a feel for how to handle the torch and lets you make mistakes without damaging the acrylic that's actually a part of your project. [7] X Research source
- If you don't have any excess acrylic, go out and buy some for this specific purpose.
-
Pass the propane torch quickly over the edges of the acrylic. If you move the torch too slowly, the acrylic will melt or burn and the material will be ruined. To be as safe as possible, make a pass with the torch and allow the edge to cool to the point where you can touch it with your hand. This helps you avoid burning the acrylic. [8] X Research source
- It usually takes a couple of minutes for the acrylic to cool off after it's been torched, so wait at least that long before touching it.
-
Go over the acrylic edges again to finish the job. It should only take 2-3 passes at most to get a quality finish, and each pass should take no longer than a few seconds. When the acrylic looks like glass, that's when you know the job is done. [9] X Research source
- Remember to allow the edges to cool before making a second and third pass over the acrylic. If you re-torch the acrylic too quickly, the material could melt or burn.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Things You'll Need
Sanding Down Your Acrylic
- 180, 320-360, and 600-grit water-proof sandpaper
- Extra pieces of acrylic
- Sanding block made of rubber or foam
- Spray bottle filled with water
- Utility knife
- Pencil
Flame Polishing Your Acrylic
- Propane torch
- Extra pieces of acrylic
References
- ↑ http://www.bcae1.com/plexi.htm
- ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
- ↑ http://www.bcae1.com/plexi.htm
- ↑ http://www.bcae1.com/plexi.htm
- ↑ http://www.bcae1.com/plexi.htm
- ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
- ↑ http://www.bcae1.com/plexi.htm
- ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
- ↑ http://www.pmma.dk/acryl_polering.aspx?Lang=en-GB
About This Article
Thanks to all authors for creating a page that has been read 83,176 times.
Reader Success Stories
- "Explained in simple terms."
Advertisement
87%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"Explained in simple terms."
