PDF download Download Article PDF download Download Article

It is super frustrating to open your washing machine only to find that it is still full of water! This can happen for several reasons, but the most common one is a clog somewhere in the system. Before checking for the obstruction, turn off the washing machine and unplug it from its power source. Then check both the drain hose and the drain pump to see if something got lodged in either of them.

Get Product Support Solve Any Problem

wH
Hi there! Do you have a question about how to use or repair your home appliance? I’ve read the manuals so you don’t have to. Select your product, brand, and model, then ask away!
*
*
Method 1
Method 1 of 2:

Cleaning out the Drain Hose

PDF download Download Article
  1. If your washing machine has an “off" or “cancel” button, press it, especially if the washer was in the middle of a load when you realized it wasn’t draining. Then, unplug the washing machine from its power source. [1]
    • The power must be turned off while you’re working on the washing machine so you don’t risk getting electrocuted.

    Tip: Use duct tape to attach the power cord to the side of the washing machine so it doesn’t accidentally get wet or in the way while you’re working.

  2. The drain hose is normally located on the back of the washing machine next to or in between the hoses for the hot and cold water. The drain hose is usually gray or black, while the water hoses are either red or blue. [2]
    • A kink in the hose could be the cause of the clog. If you see one, untwist it, turn the washing machine back on, and run a spin cycle to see if the water drains away.
    Advertisement
  3. The drain pipe is where the hose enters the washing machine. The towel or pan will help catch any water that comes out when you detach the hose. [3]
    • At this stage, don’t worry about draining the excess water from the inside of the washing machine. If the cause of the clog is in the drain hose, you should be able to clear the hose, hook it back up, turn on the machine, and run a spin cycle.
  4. Just wiggle the hose until it comes loose from the drain pipe. If the hose is stuck to the pipe, use WD-40 or something similar to loosen the connection. [4]
    • The other end of the drain hose can remain in the washbasin or main drain where it usually empties the water.
  5. You may be able to feel a blockage in the hose by gently squeezing it from one end to the other, or you can run water through one end to see if it exits the other side. [5]
    • If the water runs through the length of the hose easily, chances are that it is not the source of your clog.
    • Sometimes socks or other small clothing items can get lodged in the hose.
  6. If the hose is indeed clogged, manually unclog it with something like the end of a wire coat hanger or a plumber’s snake. Push the long-handled instrument through one end of the hose and continue pushing until the blockage has been dislodged. [6]
    • Try running water through the hose one more time to fully rinse it of any lingering debris or lint.
  7. Plug the drain hose back into the drain pipe, push the washing machine back into place, plug it in, and turn it on. Run a drain or rinse cycle to check if the water in the washing machine can now drain out through the hose. [7]
    • If this solves your problem, that is great! If the machine still isn’t draining, the problem may lie with the drain pump or some piece of internal hardware.

    Tip: After draining out the excess water from the washing machine, rewash the garments or clothes that were in the machine when it stopped working. Depending on how long the water was sitting in the washing machine, things could have started to develop mold or mildew.

  8. Advertisement
Method 2
Method 2 of 2:

Checking the Drain Pump

PDF download Download Article
  1. Not every washing machine has a power button, but turn yours off if it does. Unplug the cord from the power outlet so no electricity is running to the machine while you’re working. [8]
  2. Siphon the excess water into a 5 US gal (19 L) bucket. Pull the machine out from the wall to access the drain hose. Wiggle the drain hose off of the drain pipe, which is where it enters into the washing machine. Put the end you just disconnected into the bucket and drain out the water. Reconnect the hose to the pipe, let it fill with water, and then drain it again. Repeat this siphoning action until most of the water has been drained away. [9]
    • If there were clothes or garments in the machine when it stopped working, remove them from the washer and squeeze out the excess water before setting them to the side in a laundry basket.
    • You may need to tilt the washing machine onto its side while working on it in order to empty as much water as possible.
  3. The panel is either in the front or back of the washing machine. For older models, it may be underneath the machine; if it is, tilt the washing machine forward to get to it. You should be able to easily remove the panel with your hands. If you aren’t sure where the washing machine’s panel is, consult the owner’s manual. [10]
    • The pump is what powers the washing machine and indicates whether it should be recirculating water or draining water out of the drain hose.
    • If the pump gets clogged or stuck, the machine won’t be able to drain away excess water.
    • This panel will likely be on the front of a front-loading washer. [11]
  4. Next to the pump, you should see a filter cap that covers the actual filter itself. Unscrew the cap and examine the filter for gunk or debris that could be clogging your machine. Rinse it off or use a damp cloth to wipe it down. [12]
  5. The impeller is a rotating hub that agitates the water in the washing machine. With the filter cap still removed, run your fingers along the inside of the impeller to see if it moves easily. If it doesn’t, there may be something small like a coin or small sock in the way. Remove any blockage you find; you could use tweezers or pliers to pull out small blockages. [13]
    • Be careful that your fingers don’t get stuck or pinched in the impeller.
  6. Replace the filter cap, close the washing machine panel, reposition the machine, and plug it back in. Try running a small load of just water to see if the machine will now drain. [14]
    • If this doesn’t resolve the issue and you’ve already checked the drain hose, there most likely is a mechanical problem that needs to be addressed.
  7. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      • If the washing machine still isn’t working after you checked for clogs, it may be that the water pump or drive belt needs to be replaced. It’s also possible that the lid switch may be faulty. These repairs often require the help of a professional.
      • Every 4-6 weeks run a load with just hot water and detergent to clear away any excess gunk.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Warnings

      Advertisement

      Things You’ll Need

      Cleaning out the Drain Hose

      • Duct tape (optional)
      • Towel or small pan
      • WD-40 (optional)
      • Wire coat hanger or other long-handled instrument

      Checking the Drain Pump

      • 5 US gal (19 L) bucket
      • Washcloth
      • Rubber gloves (optional)
      • Tweezers or pliers

      About This Article

      Thanks to all authors for creating a page that has been read 77,792 times.

      Reader Success Stories

      • Threnody C.

        Feb 29

        "It gave me a couple of ideas where to check for solutions to my problem before calling a repair man. I'd much ..." more
      Share your story

      Did this article help you?

      Advertisement