How to Label a Blood Sample

PDF download Download Article
PDF download Download Article

After collecting blood, the tubes must always be properly labelled to ensure positive patient and specimen identification. This is a general guide for knowing how to label a Vacutainer tube using computer-generated adhesive labels. [1] Practitioners should always refer to their facility's resources for specific procedures.

Steps

PDF download Download Article
  1. Ask the patient to state their first and last name and their date of birth. Confirm this information against your labels as well as the patient's hospital wristband (if inpatient) or health card (if outpatient). If using a hospital wristband, you should also match the patient's health number or medical record number (MRN) if present and if your hospital policy dictates. [2]
  2. Perform venipuncture according to your facility's protocols and procedures. As soon as the collection is over, engage the safety feature on the needle to prevent a needlestick injury. Invert all tubes to adequately mix the blood with the additives. [3]
    Advertisement
  3. Tubes should always be labelled immediately after venipuncture in front of the patient. Do not exit the patient's room or allow the patient to leave until all your tubes have been labelled. [4]
  4. 4
    Peel the label off its backing and stick it on your finger.
    • A typical blood specimen label has the following information on it: [5]
      • Patient's first and last name.
      • Date of birth, age, and sex.
      • MRN or health number plus the lab accession number.
      • The tests to be performed on that specific sample.
      • The tube colour or type, varies by facility. (In these images: LAV = lavender top EDTA; GOLD = gold top SST; LT GRN = light green PST)
      • A barcode to be scanned for specimen tracking and analysis.
  5. 5
    Hold the tube horizontally so that the coloured stopper is facing left.
  6. Ideally, the lab label should be covering the tube manufacturer label to leave a small window so the specimen is still visible. The left edge of the label should be directly against the tube stopper. [6]
    • It helps to roll the tube with your hands or fingers to ensure complete adhesion.
  7. 7
    Repeat for your remaining tubes. Always label one tube at a tube.
  8. Labels should not:
    • Be crooked or slanted. The barcode should be straight.
    • Be wrinkled, creased, or torn.
    • Be wrapped around the tube so the barcode is perpendicular, or folded over itself like a "flag".
    • Be covering the specimen window, obscuring the view of the sample.
  9. 9
    Follow specific downtime procedures if IT failures prevent you from generating labels. At minimum, handwrite the patient's first and last name, MRN or health number, date of birth, time of collection in 24-hour format, and your initials or employee ID. You should write this information on a blank specimen label or on the tube manufacturer label using indelible blue or black ink.
    10. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!

      Warnings

      • The person who collects the blood sample is ultimately responsible for the accuracy of patient identification and specimen labelling. A mislabelling situation occurs when a label is placed on the wrong tube or when a specimen is labelled with a different patient's label. Because many clinical decisions are supported by lab tests, errors in labelling can have profound adverse effects on patient care and safety if left uncaught. Always take the time to ensure you have correctly identified your patient and positively matched your specimen labels.
        Thanks
        Helpful 0 Not Helpful 0
      • Never pre-label your tubes. Tubes should always be labelled after the blood has been collected.
        Thanks
        Helpful 0 Not Helpful 0
      • Be diligent in your label placement. Many lab tests are automated, and analysis might be delayed if the barcode cannot be scanned due to crookedness or wrinkles.
        Thanks
        Helpful 0 Not Helpful 0
      Advertisement

      You Might Also Like

      7 Easy Ways to Figure Out Your Blood Type (With or Without a Test)
      How to
      Draw Blood
      How to
      Troubleshoot a Difficult Venipuncture
      How to
      Test Blood to Make Sure It's Real
      How to
      Read Blood Test Results
      How to
      Read and Understand Medical Laboratory Results
      How to
      Prick a Finger for a Blood Spot Test
      How to
      Find Out Your Blood Type at Home
      Advertisement

      References

      1. ↑ https://www.pathology.uci.edu//services/specimen-containers.asp
      2. ↑ https://www.pathology.uci.edu/services/specimen-labeling-requirements.asp
      3. ↑ https://pathlabs.ufl.edu/client-services/specimen-shipping/blood-collection-process-venipuncture/
      4. ↑ https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4622200/
      5. ↑ https://pathlabs.ufl.edu/client-services/specimen-shipping/blood-collection-process-venipuncture/
      6. ↑ https://www.youtube.com/watch?v=SHSfIT2Rvyw

      About This Article

      Thanks to all authors for creating a page that has been read 20,108 times.

      Did this article help you?

      Advertisement