Download Article
Download Article
Garage door sensors protect your family, possessions and pets by not allowing the heavy garage door to close if there is anything in the glide path. They do this by using an electric eye sensor that crosses the doorway. If the sensor doesn't receive the beam emitted by its opposite number, the door won't close. This seems like a clever device until the components come out of alignment -- meaning the door won't close at all. Fortunately, it's not difficult to realign the sensors and put things back into working order
Get Product Support Solve Any Problem
Try Asking:
We’re sorry we don’t have the product, brand, or model you are looking for. Please enter its name below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
Steps
Download Article
-
Turn off the power to your sensors by tripping the fuse for your garage. You'll find this in your home's breaker box.
- You won't actually be working with the electrical wiring, but it's always best to be safe when working with electricity.
- It doesn't hurt to check the wiring first to ensure that your garage door sensors are receiving power.
-
Loosen the screws that mount each of your garage door sensors. Don't take them all the way out. Just loosen them enough so that the mounting brackets can slide up and down, but won't do so unless you intentionally move them. [1] X Research sourceAdvertisement
-
Slide each garage door sensor downward so it is as low as possible without unscrewing the mounting brackets. [2] X Research source
-
Tie a string to one sensor so that, if pulled across the garage doorway, it will run across the center of the sensor.
-
Run the string across the garage doorway and tie to the opposite sensor. Position the knot so the string runs across the center of that sensor, too.
-
Lay a level so the bottom runs along the string. Check that the line of the string is level.
- If the line of the string isn't level, adjust 1 or both garage door sensors by sliding the mounting bracket upward. Continue until the sensors are once again level.
-
Tighten the screws to secure the garage door sensors in their new position.
-
Confirm that the string is level before finishing. The sensors may have come out of alignment when you tightened the screws. [3] X Research source
-
Finish by removing the string and turning the power to your garage back on.
Advertisement
Community Q&A
Search
-
QuestionOne sensor is green and the other yellow. Why is that?Community AnswerThe "orange/red" eye is putting out the infrared beam to the "green" receiving eye. If the green is not lit or blinking, it needs to be adjusted until it is a steady ON green or the door will not operate.
-
QuestionI have a wall-mounted controller to open and close my garage door. When I push the close button on the controller, I have to hold it down until the garage door is completely closed. What can I adjust or fix to make the garage door close with just a push of the button?Community AnswerIt sounds like your sensors are out of alignment. You are bypassing the safety by holding the button down. Check to see if the light on each sensor is on and then realign from there.
-
QuestionHow high off of the ground should the garage door sensors be located?Community AnswerThey should be 6-9" off the floor, and make sure they're equal. There should be an LED indicator light on the top or back of each unit that lights up when the sensors are parallel and aligned. You may have to adjust the sensor brackets up and down or side to side to achieve this.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If you have a laser level, you can use it instead of a string to align your garage door. In this case, you will set up the level aligned with one sensor, then adjust the opposite sensor until the beam of your laser level is hitting the sensor.Thanks
- Proper height for a garage door sensor is 4 to 6 inches (10.2 to 15.2 cm). Higher than that can miss many low-lying objects, including pets. Lower is easy to stand above with a foot on either side. If your garage door sensors are outside of this range, remove them entirely from the garage door frame and install, leveled, inside the safe zone.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- Screwdriver or power screwdriver
- String, 10 to 15 feet (3.0 to 4.6 m) long
- Level
Expert Interview
Thanks for reading our article! If you'd like to learn more about dealing with a garage door, check out our in-depth interview with Ryaan Tuttle .
References
About This Article
Thanks to all authors for creating a page that has been read 364,047 times.
Reader Success Stories
- "Funny and very informative. I'll help my kids fix their garage door sensor from what I learned from you. Thank you very much." ..." more
Advertisement
83%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"Funny and very informative. I'll help my kids fix their garage door sensor from what I learned from you. Thank you very much."
..."
more
"Answered in detail exactly the questions I had in a humorous and entertaining way."
"The pictures!! The video!! Thank you so much for the guidance."
"Very easy explanation with pictures on how to do this job."
"The wire connections to the sensor - helped me."
