Download Article Download Article

Long stem roses make a beautiful Valentine’s day gift or a spontaneous, "just because" purchase. These flowers have a sweet fragrance and add elegance to any room, especially if they are arranged correctly. Start by trimming the roses and filling a vase with water. You can then arrange them with the help of clear tape and add other items like ribbons, glass beads, or greenery to give the roses a little something extra.

Part 1
Part 1 of 3:

Trimming the Roses

Download Article
  1. Always cut at a downward angle so the roses are able to soak up the water in the vase. Make sure all the stems are the same height. [1]
  2. This will give the roses a nice, long-stemmed appearance. To maintain as much of the long stems as possible, look for a vase that's around 12 inches (30 cm) tall. [2]
    Advertisement
  3. Anything in the bottom two-thirds of the vase will be below the waterline. It's important that you take off the leaves so they don't sit in the water and develop mold. To take the leaves off, just gently pull on them with your fingers. [3]
    • Be careful of any thorns on the stems, as you do not want to prick yourself. Wear gardening gloves when you remove the leaves to be safe.
  4. Advertisement
Part 2
Part 2 of 3:

Creating a Taped Grid

Download Article
  1. Use filtered water in the vase to ensure it is free of impurities. [4]
    • To make the roses last longer , you can pour 1 to 2 tablespoons (15 to 30 ml) of powdered flower food in the water and stir it in.
  2. Attach the tape to 1 end of the opening on the vase and extend it in a straight line to the other end. Continue lining up at least 4-5 pieces tape next to each other so they all face the same direction. Leave 1 to 2 inches (2.5 to 5.1 cm) of space between each piece of tape. [5]
    • Make sure the tape is flush to the edge of the vase so the excess tape isn't visible when you put the roses in.
    • Use clear cellophane tape so it's not as noticeable.
  3. Place a piece of tape in the other direction on the opening of the vase. Layer 4-5 pieces of tape in the other direction over the first row of tape, creating a grid. [6]
    • Attach the same number of pieces of tape going in both directions so the grid is even.
  4. The grid should prevent the roses from leaning to one side. If you run out of squares on the grid, start doubling up by putting 2 roses in each square. [7]
    • Make sure you angle the roses so the stems fall in the same direction in each row, as this will allow them to sit more evenly in the grid.
  5. If you notice any of the stems are sitting a bit higher than the others, take it out of the water and use gardening shears to trim it down to size. You want all of the stems to sit at the same height in the vase so they look uniform and even. [8]
  6. Advertisement
Part 3
Part 3 of 3:

Adding Greenery and Other Details

Download Article
  1. Use greenery like myrtle, ivy, or leather fern to give the roses more texture and color. Place the greenery around the edges of the vase so they do not overpower the roses. Slide them into the squares on the grid next to the roses so they sit upright. [9]
    • Make sure you trim the greenery as needed before you put it in the vase so it is the same height, or just a bit taller, than the roses. Always trim the greenery at an angle with sharp gardening shears.
  2. Before you make the tape grid and add your flowers, fill three-quarters of the vase with the beads. When you add the flowers to the vase, gently press the stems down through the beads until they reach the bottom. Then, water the roses like you normally would. [10]
    • Make sure the glass beads are clean and free of dirt or dust, as you do not want it to get into the water in the vase.
  3. Another option is to put a decorative ribbon or piece of fabric around the vase. You may opt for a seasonal ribbon in holiday colors for a festive look or a brightly colored ribbon to contrast the muted color of the roses. [11]
  4. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    What do you put in a rose bouquet?
    Lana Starr, AIFD
    Certified Floral Designer & Owner, Dream Flowers
    Lana Starr is a Certified Floral Designer and the Owner of Dream Flowers, a floral design studio based in the San Francisco Bay Area. Dream Flowers specializes in events, weddings, celebrations, and corporate events. Lana has over 14 years of experience in the floral industry and her work has been featured in floral books and magazines such as International Floral Art, Fusion Flowers, Florist Review, and Nacre. Lana is a member of the American Institute of Floral Designers (AIFD) since 2016 and is a California Certified Floral Designer (CCF) since 2012.
    Certified Floral Designer & Owner, Dream Flowers
    Expert Answer
    Don't just limit yourself to roses! To make an arrangement of roses look even more special, try adding lush foliage to the bouquet because the leaves on roses are going to wilt after just a few days. You can also add a long, thin grass like beard grass to the vase, which will create a beautiful fountain look when it's combined with the roses.
Ask a Question
      Advertisement

      Tips

      • To replace the water, remove the flowers from the vase and gently drain the water into the sink. Pour slowly so the water does not damage any of the tape and refill the vase with fresh water. If any of the tape rips, replace it before putting the flowers back in the vase.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!
      Advertisement

      Things You’ll Need

      • Long stem roses
      • Vase or container
      • Clear tape
      • Scissors

      About This Article

      Thanks to all authors for creating a page that has been read 27,549 times.

      Did this article help you?

      Advertisement