Download Article Download Article

A blind hem stitch is a classic way to tailor trousers or skirts to the right length. This barely-visible hem creates a crisp, clean appearance and is easy to do with just a bit of practice. Many sewing machines have a special foot for blind hems, but you can make the stitch on a machine even without this attachment. Once you master the process, you'll find yourself spending a lot less on alterations!

Part 1
Part 1 of 3:

Preparing the Garment

Download Article
  1. You can do this with a seam ripper or small nail scissors. Or, if the garment is much longer than desired, you can cut off the bottom with fabric scissors.
    • Don't make the garment too short, though! Leave several inches to prepare your blind hem.
    • Stand on a stool or table and ask a friend to put a few pins at the correct level.
    Advertisement
  2. Remove the pins.
    • Use water-soluble pencil, pen, or chalk.
    • Alternatively, you can mark the hemline with pins.
  3. Watermark wikiHow to Blind Hem Stitch
    For example, if you want a 2-inch deep hem, you mark a line 2 inches (5.1 cm) above and 2 inches below the hemline.
    • Again, you can use a water-soluble pen or pencil, or do this with pins.
  4. Be certain to leave an inch of fabric!
  5. Watermark wikiHow to Blind Hem Stitch
    If you have 1 inch (2.5 cm) of raw edge, tuck 1/2 inch (5.1 cm) of fabric under, leaving the remaining 1 2 inch (1.3 cm) under your bottom line.
    • Some experts suggest sewing this fold with a basic straight stitch or finishing the raw edge with an over edge or zigzag stitch, but this may not be an essential step. [1]
  6. Watermark wikiHow to Blind Hem Stitch
    Do this by pinching the fabric at the middle line (what's to be your final hemline). Your other two lines (above and below the hemline) should line up, since they are equidistant from the hem. Pin around the hem to hold this fold in place.
  7. Watermark wikiHow to Blind Hem Stitch
    At this point, your bottom line will once again be exposed, and below it the pressed raw edge.
    • You can remove the previous pins and use them to secure the folds.
  8. After you've done this, you can remove the pins if you wish, but it isn't necessary. [2]
  9. Advertisement
Part 2
Part 2 of 3:

Preparing Your Sewing Machine

Download Article
  1. The sewing machine requires a specific foot for this stitch, with the vertical bar passing between the two feet.
    • Alternatively, buy a universal blind hem presser foot for your machine in a sewing shop or online. These feet are fairly inexpensive and a good choice if your machine does not have the blind hem presser foot. [3] Make sure, however, that it fits your machine. Check the product specifications before buying: they'll usually say which machines it works with.
    • If you can't find a presser foot for your machine, you can still make this hem! Skip to sewing instructions in Part 3, Step 2.
  2. Watermark wikiHow to Blind Hem Stitch
    Follow the instructions for your particular machine.
  3. This setting is often indicated by two stitches spaced far apart, but check your user's manual to be sure. Now you're ready to sew! [4]
  4. Advertisement
Part 3
Part 3 of 3:

Sewing the Blind Hem Stitch

Download Article
  1. Make sure the foot's vertical plate is sitting right on top of the fold. The machine is going to stitch along the raw edge section mostly, but cross the plate into the fold every few stitches.
  2. Watermark wikiHow to Blind Hem Stitch
    Hold the fabric carefully so that the fold stays just under the vertical plate. This way the needle is sure to catch it. [5] If you do not have a blind hem presser foot, make the stitch pattern manually:
    • Put the machine feed dogs on the inside.
    • Place your fabric on the machine as in Step 1.
    • Make five straight stitches, and then one stitch to barely catch the fold.
    • Continue around the hem.
  3. Watermark wikiHow to Blind Hem Stitch
    Remove the garment, snip the thread, and turn right side out. Check for any missed stitches.
    • If needed, go back and redo the sections where there is a missing stitch.
  4. If a line remains from the previous hemline, try spritzing it with a bit of distilled water and ironing. If this doesn't work, it will probably come out when laundered. [6]
  5. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you blind stitch fabric that is really thick?
    Essie Karimi
    Professional Tailor
    Essie Karimi is a Professional Tailor and the Owner of Sew Fit Tailoring & Alterations, a sewing shop that has been operating for over 40 years. Essie specializes in tailoring, alterations, sewing, repairs, and redesign. Essie works on a variety of clothing types, including wedding dresses, formal wear, casual wear, sportswear, swimwear, and uniforms.
    Professional Tailor
    Expert Answer
    Use a needle and thread! Thick fabric can cause the needle to break when you're using a machine.
Ask a Question
      Advertisement

      Video

      Tips

      • It is best to practice on scraps of fabric before hemming your item of clothing; this way you can perfect your technique without damaging your pants or skirt.
      • Always read and follow the instructions for your sewing machine.
      • The blind hem stitch is perfect for curtains, as well.
      Show More Tips
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!
      Advertisement

      About This Article

      Article Summary X

      To blind hem stitch, first remove the seam from the existing hem. Next, mark or pin the newly desired length for the hem. Trim the raw edge, leaving 1 inch below your lowest line, then fold the edge in and press it with an iron. After ironing, pin around the fold to hold the new hem in place. Attach the blind hem presser foot to your sewing machine, turn your garment inside out, and slowly stitch your hem. For tips on how to finish your hem without the blind hem presser foot attachment, keep reading!

      Did this summary help you?
      Thanks to all authors for creating a page that has been read 76,708 times.

      Reader Success Stories

      • Suzie Knitter

        Jan 2, 2018

        "Very clear instructions. Thank you for using a thread we can see for the example!"
      Share your story

      Did this article help you?

      Advertisement