PDF download Download Article PDF download Download Article

A log bed is a bed frame built entirely from logs that are cut and shaped to fit together without nails or screws. Early log beds were made with crossrails and topped with a mattress. Modern log beds hold a box spring as well as a mattress , and so have no need for crossrails.

Method 1
Method 1 of 2:

Preparing the Logs

PDF download Download Article
    • The best choice is a log from a fire-killed standing dead tree. A wildfire burns diseased trees to the ground, but leaves healthy trees dead but still standing. Therefore, your chances of getting good logs are best from these trees. Fire-killed wood also loses its bark, saving you time when you start building. [1]
    • You can find fallen logs or logs that wash onto a beach or riverbank. You can also buy logs from a sawmill. However, you may find after you start working that these are rotten or have other problems that make them unsuitable.
    • Cut live trees down to get logs if it's legal to do so. You will have to wait about a year for the wood to dry enough to build with it. Stripping the bark will help it dry faster.
    • Saw 2 4-foot (1.2 m) posts and 2 3-foot (90 cm) posts to make the legs and the ends of the headboard and footboard. The posts should be cut from large, sturdy logs.
    • Saw 4 rails to separate the posts. Measure the mattress width and cut the rails to be 1 inch (2 to 3 cm) longer. When you cut the tenons to fit the rails into the posts, they will be the width of the mattress.
    • Cut spindles to place between the rails of the headboard and footboard. You need 36-inch (90 cm) spindles for the headboard and 24-inch (61 cm) spindles for the footboard. After cutting the tenons, they will measure 1 inch (2.5 cm) shorter. The number of spindles you need depends on the size of the bed.
    • Prepare 4 bed rails to connect the headpost to the foot post on each side. Measure the mattress length and cut the bed rails so they're 1 inch (2 to 3 cm) longer.
    Advertisement
  1. These are blades with 2 handles that you set against the wood and pull toward you. A curved drawknife removes bark and a straight drawknife shapes the log. [2]
  2. You can do this with a drawknife, but it's easier to do with a tenon maker, which attaches to a drill and operates like a giant pencil sharpener.
  3. Frostner bits drill flat-bottomed holes large enough to hold tenons. [3]
    • Mortises for the headboard should be cut at 9 inches (23 cm) and 44 inches (1.1 m) from the floor. For the footboard, the mortises are cut at 9 inches (23 cm) and 32 inches (80 cm).
    • Spindle mortises are cut so the spindles will be evenly spaced.
    • Mortises for the bottom bed rail are drilled at 5 inches (13 cm) above the floor in all 4 posts. The mortises for the top bed rail are drilled at 13 inches (33 cm) from the floor.
  4. Advertisement
Method 2
Method 2 of 2:

Assembling the bed

PDF download Download Article
  1. Place the eye hooks so you can stretch a cable between the right headpost and left footpost and the left headpost and right footpost. [4]
  2. Use turnbuckles in the centers to tighten the cables and hold the bed together. Adjust as necessary to make sure the bed is square.
  3. [5]
  4. Advertisement

Video

Community Q&A

Search
Add New Question
  • Question
    How do you fix a long cracs on a bed post?
    Community Answer
    Long answer short: you can't. However, you can use wood filler, then sand and wax. It will never look the same but it will add character.
  • Question
    How round do the cedar logs need to be for the bed post and the railing?
    Community Answer
    You could do this same build with square posts and it would be okay. However, if the logs are a lot bigger at one end than the other, you might have to change the length of a higher or lower railing to make it fit together correctly.
Ask a Question
      Advertisement

      Tips

      • You can buy a log bed kit that has logs that are already cut for the size of your bed, drilled and tenoned so you only have to assemble the bed.
      • Don't worry if there are cracks in the logs. This is a natural feature of dry wood. If you turn the logs so as to avoid drilling mortises into the cracks, the logs will be just as strong as those without cracks.
      • Consider using logs that have knots, aren't quite straight of have other unique characteristics.
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!
      Advertisement

      Things You'll Need

      • Logs
      • Circular or hand saw
      • Measuring tape
      • Drawknives
      • Drill
      • Forstner bits
      • Tenon maker
      • Eye hooks
      • Steel cables
      • Turnbuckles


      About This Article

      Thanks to all authors for creating a page that has been read 217,420 times.

      Did this article help you?

      Advertisement