Download Article
Download Article
Why Does My Furnace Keep Shutting Off? Is your furnace having trouble staying on once it fires up? Does it quickly shut off, after you start it? Does it do this a few times and then fully shuts down? Many homeowners have this problem every year because of a dirty flame sensor. Heating, Ventilation, and Air Conditioning is a complex industry, but this repair is simple enough that you can perform by yourself. In our example will show a gas-fired furnace, but you can find flame sensors in boilers and other gas-burning appliances.
Steps
Download Article
-
To avoid danger, it is very important to shut off the power to your furnace (or any other appliance), prior to making any repairs. There will usually be a light switch (toggle switch) on or near your furnace. If this switch is not present, furnaces have a dedicated breaker; locate your furnace breaker and shut your unit down.
- NOTE: Turning off the thermostat does not shut down the power to your unit. Also, there are many different types of furnaces and appliances; if your gas valve is not electrically controlled, you will need to shut off the gas to the unit as well. Should you be confused about any of the information provided here, because it does not match with what you see on your unit, STOP! Do not guess or assume anything when dealing with your heating system. Call an HVAC professional in your area, in order to complete the repair on your unit.
-
Remove the Sensor. In the video, you can see 4 burner ports. Between the 1st and 2nd burner ports (from left to right), you can see the wire leading to the flame sensor.The sensor is easily accessible and typically mounted by one 1/4” hex head screw. Upon removing this screw, the sensor will slide out so that you can easily clean it. Carefully remove the sensor; it may be necessary to detach the wire fixed to the end of it to get more room to work, but this is not usually necessary.Advertisement
-
Clean the Sensor. Once you have removed the sensor, gently rub the metal rod (only) with soft steel wool or soft scotch brie type pad NEVER USE SANDPAPER as it will damage the flame rod. Remember, you are not sanding down an auto body, but simply ridding the sensor of any build up it may have. Then, use a clean paper towel to wipe clean any dust left behind .
-
Replace the Sensor. Once you’ve cleaned the sensor, simply reconnect the wire if you’ve taken it off, remount the sensor to the burner assembly using the 1/4” screw, replace the door(s) on the unit, and turn the power back on.
-
Check Your Results. If the unit takes a few extra seconds to start up or the fan immediately kicks on and runs for a bit, this is normal. Shutting down the power to the unit can cause it to reset and run through a short series of checks before trying to fire again. Once this check is complete, the unit should begin to operate by command of the thermostat. Make sure the unit re-fires and runs properly until the thermostat is satisfied, at least once before being confident your problem is solved.
-
How to Replace a Broken Flame Sensor. If cleaning your flame sensor did not work, it’s possible that the sensor is broken and that the furnace is operating as it should. You may need to replace the sensor, in which case you can follow these same instructions with the exception that no sanding is involved; just remove one sensor and replace it with a new sensor. Of course something else could be causing the problem and at this point, you should contact a service repair technician.
Advertisement
The Takeaway: Removing & Cleaning a Flame Sensor
Shut off power to the furnace and loosen the hex head screw holding the sensor in place (you may need to detach the wire connected to the sensor as well). Use steel wool or a cleaning pad (never sandpaper) to rub away debris from the metal part of the sensor only. Replace the sensor.
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Warnings
- Simple is the keyword in this process, but most furnace related service work is not very simple and show be performed by an HVAC professional.Thanks
Advertisement
Things You'll Need
- 1/4” Hex Driver or Wrench (This could vary based on your type of mounting screw)
- Small piece of light grit sandpaper, steel wool, or emery cloth
- Dry and Clean Paper Towel
About This Article
Thanks to all authors for creating a page that has been read 91,774 times.
Advertisement
88%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
