How to Convert an Airsoft Gun from an AEG to an HPA

PDF download Download Article
PDF download Download Article

Many people want to convert their airsoft AEG to an HPA, as it is easy to adjust the FPS, it is quiet, it has an instant trigger response, and makes your shot more consistent. Although, after converting you will need an HPA rig, which includes the air tank, a regulator, and something to carry the air tank in. Before beginning, make sure your primary field allows HPA setups, as some fields don't.

Steps

PDF download Download Article
  1. Every gun is different, but you should be able to get to the internals by popping out pins and screws that keep the body halves together. Make sure you keep the screws.
    • Once the body is separated, you should see a large metal piece that would have some wires running into it. This piece is the gearbox.
    • There may be some screws holding the gearbox down, if so you can remove them.
    • Remove the gearbox from the gun by lifting the gearbox and the motor (a cube like structure likely located in the pistol grip). Set them aside and move the body out of the way.
  2. You can open the gearbox by removing screws keeping the halves of the gearbox intact. Make sure that the front of the gearbox is on your right. You can now lift up the top shell of the gearbox, which should reveal many gears and pistons.
    Advertisement
  3. You will need a screw-driver for some of this. You will want to remove things in this order:
    • Spring and buffer-tube/spring-guide. Make sure you keep the buffer-tube/spring-guide.
    • The bevel gear. This is the gear the will be closest to you.
    • The piston system.
    • The other two gears.
    • The trigger and trigger spring. You will need to keep these and the trigger screws for later on.
    • The trigger contacts and wiring.
    • Anything else left in the gearbox.
  4. Using the trigger screws you removed, place the trigger board where the trigger contacts once were, and screw it in.
  5. Take the main module and place it where the piston once was, making sure the notches on the gear box and main module are aligned.
  6. Take the wiring from the main module and plug it in to the trigger board.
  7. Take the wiring harness and snap it into the trigger board.
  8. The tub should be run down the pistol grip area of the gearbox.
  9. The wiring harness will follow the path of the cables going to the battery that were removed.
  10. Put it back in just as you removed it. Place the trigger over the trigger spring. Make sure that the trigger and trigger spring are aligned correctly.
  11. Make sure it is facing toward the main HPA unit.
  12. Put the other half of the gearbox back on, make sure nothing is getting pinched, and screw the halves back together.
  13. You can now close the gun, and you are finished.
    14. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What is a wiring harness?
    Kurtis Hardy
    Community Answer
    Wiring harnesses are what come with an HPA unit to hook from the trigger board to the Fire Control Unit (FCU). Most electronic HPA units will come with everything needed to assemble it into your favorite Airsoft replica.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 2 Helpful 4
  • Question
    Where can I find an HPA engine?
    Kurtis Hardy
    Community Answer
    Airsoft HPA engines are available from many Airsoft vendors. One vendor that is highly recommended is Amped Airsoft. They offer a wide variety and can also be purchased in kits with everything you need to install.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 4 Helpful 9
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!

      Things You'll Need

      • Philips head screwdriver.
      • A set of Allen wrenches.
      • HPA setup.
      • An airsoft AEG.

      You Might Also Like

      How to
      Make an Airsoft Grenade
      How to
      Play Sepak Takraw
      How to
      Play Lacrosse
      How to
      Play Handball
      Scoring in Curling: Everything You Need to Know to Understand the Game
      How to
      Play Muggle Quidditch
      How to
      Win in Dodgeball
      A Beginner’s Guide to Playing Gaga Ball
      How to
      Throw a Dodgeball
      How to
      Play Dodgeball
      How to
      Make a Shuffleboard Table
      How to
      Invent a Sport
      How to
      Play Netball
      How to
      Shoot in Netball
      Advertisement

      About This Article

      Thanks to all authors for creating a page that has been read 78,052 times.

      Did this article help you?

      Advertisement