Download Article
Download Article
Memory foam is a common material used for mattresses and pillows since it is relatively comfortable and it conforms to your body. If you have a piece of memory foam that’s too large, you can easily cut it at home with an electric carving knife. Be sure to double check your measurements before you make your cut so you don’t make a mistake. When you’re finished, you’ll have a piece of memory foam that’s the perfect size!
Steps
-
Remove the slipcover if you’re cutting a memory foam mattress. Many new memory foam mattresses have a slipcover on top for an additional layer of protection. Look for a zipper around the edge of the mattress and unzip it as far as you can. Once the zipper is undone, pull the edges of the slipcover off of the mattress and remove it. Since you’re cutting mattress, you can either throw away the slipcover or use the material to make a new slipcover. [1] X Research source
- If there isn’t a zipper around the edge of the slipcover, then you may need to cut it off with a knife or pair of scissors.
-
Check the dimensions you need and add 1 ⁄ 8 in (0.32 cm) to them. Use a tape measure to double check the height, width, and depth for the foam you need for your project. For example, you may measure a mattress if you’re cutting a memory foam topper, or you may find the dimensions of a pillowcase if you’re making a pillow. Add 1 ⁄ 8 inch (0.32 cm) to each measurement you take since cutting the foam could remove some of the material. [2] X Research sourceAdvertisement
-
Mark the memory foam with a permanent marker and a tape measure. Hold the end of your tape measure at the edge of your piece of memory foam and pull it out until you reach the correct length. Draw a dot on the memory foam with a permanent marker at the end of your measurement. Move your tape measure along the edge of the mattress by 10 inches (25 cm) and make another dot so it’s in line with the first one. Continue marking the memory foam until you reach the other side. Repeat the process for any other dimensions you plan on cutting. [3] X Research source
- Double check your measurements to make sure they’re accurate, or else you may make a crooked cut.
Warning: Be careful not to compress the memory foam while you’re taking your measurements, or else they may not be accurate.
-
Draw your cut lines on the foam with a marker. Set a straightedge on top of the memory foam so it crosses the marks you made for your measurements. Use a permanent marker to draw your lines between the measurements so you know where to make your cuts. Make the lines thin so your cuts and measurements are precise. [4] X Research source
- If you’re drawing a curved line, use a round object as a stencil, such as a coffee can or a bowl.
Advertisement
-
Set the foam on a table so the side you’re cutting hangs over the edge. Find a flat, sturdy table to set your memory foam on. Position the memory foam on the table so your cut lines overhang the edge of the table. That way, you won’t damage the tabletop when you cut through the foam. [5] X Research source
- Set a heavy object on a piece of memory foam to help hold it in place if it tips over the edge. Make sure the object is at least 4–5 inches (10–13 cm) from your cut line so the foam doesn’t compress.
-
Hold an electric carving knife perpendicular to the memory foam. Plug in your electric carving knife and hold it with your dominant hand. Position the knife so the blade is at a 90-degree angle to the edge you’re cutting to make a smooth, straight cut. Make sure the serrated edge is touching the memory foam and lines up with the line you drew.
- You can buy an electric carving knife from any kitchen supply store or online.
- An electric knife will give you the smoothest cut, but you can also use a serrated bread knife if you don’t have an electric one.
-
Guide the knife along the line you drew on the foam. Turn on your electric carving knife and slowly follow along the marker line. Keep your knife perpendicular to the foam so your cut isn’t crooked. Avoid pushing down on the foam while you’re cutting since it could deform and make your cut inaccurate. Continue pushing the blade through the foam along the line until you cut through its entire length. When you need to pull the knife blade out of the foam, turn it off before removing it. [6] X Research source
- Keep your fingers and the knife cord away from the blade while it’s running so you don’t hurt yourself.
- If you’re using a serrated bread knife, saw back and forth to make your cuts.
Tip: Lay a straightedge along the line to use as a guide while you’re cutting if you need help keeping the knife straight.
-
Cut along the line again if the blade didn’t go through the foam. If you’re cutting through a thick piece of memory foam, your knife blade may not cut through it completely. Put the carving knife blade at the end of the cut again and follow along the line again. Work slowly so your cut stays straight and accurate. Continue doing multiple passes over the cut until the blade goes completely through the foam. Repeat the process for any other dimensions you need to cut from the memory foam.
- You can also flip the piece of foam over to the other side and take your measurements again. Cut through the memory foam so your 2 cuts meet in the middle.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- You can use a razor knife or serrated bread knife if you want, but it won’t make as clean of a cut. [7] X Research sourceThanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Warnings
- Keep your fingers and the knife cord away from the blade while it’s turned on.Thanks
Advertisement
Things You’ll Need
- Tape measure
- Marker
- Straightedge
- Table
- Electric carving knife
References
About This Article
Thanks to all authors for creating a page that has been read 127,827 times.
Reader Success Stories
- "It worked great! I used an electric knife to make the entire pillow a bit thinner. I started with a clean cut along one side of the pillow then had someone hold the cut open to continue the cut. Thank you." ..." more
Advertisement
92%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"It worked great! I used an electric knife to make the entire pillow a bit thinner. I started with a clean cut along one side of the pillow then had someone hold the cut open to continue the cut. Thank you."
..."
more
