How to Design a Simple Antenna

Download Article

Author Info

Last Updated: June 29, 2023

Download Article

This article will show you how to build a monopoly for any use you see fit.

1

Choose a frequency.

Download Article

For Wi-Fi you are using 2.45GHz = 2,450,000,000Hz). This is needed because this determines the length of your antenna.

2

Get a conductor.

Download Article

For the example we can use a copper wire and a piece of copper plating. Also you will need a co-axial cable (75 ohm is better than 50 ohm, for Wi-Fi 50 ohm is better than 75 ohm).

3

Determine the wire length.

Download Article

This is done by using the frequency value from step 1 to find the wavelength of the signal. To do this you simply need to divide the speed of light (c = 299 792 458 m/s) by the frequency (f). In the case of 2.45GHz the wavelength is 12.236 centimeter (4.8 in). Usually monopole antennas are quarter-wavelength structures, so the length of the wire should be 12.236/4 = 3.0509cm

4

Cut the wire.

Download Article

Cut about 3.2 centimeter (1.3 in) for a quarter-wave monopole. This way you can pare it back based on performance (and "tune" if needed) .

5

Form a ground-plane.

Download Article

Simply use the copper plate that you picked up earlier. It should be at least half a wavelength square.

6

Drill a hole.

Download Article

The whole should be just big enough for the co-axial cable to fit through.

7

Pare the coaxial cable.

Download Article

This can be pulled back to reveal the inside insulator.

8

Feed the cable through.

Download Article

The ground conductor is now above the ground-plane. Fold the ground conductor back and solder it to the copper ground plane.

9

Reveal the signal conductor.

Download Article

10

Solder the wire.

Download Article

You now have an antenna.

Community Q&A

Search

Add New Question

Question

What metal is in copper plates?

Community Answer

Presumably, copper, as it's called a copper plate.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 3 Helpful 35
Question

Which direction should I set the antenna?

Denneisk

Top Answerer

You should point the antenna in a direction that would make it most useful, e.g. point an antenna connected to your router toward the opposite end of the house.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 6 Helpful 10

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

The radiation pattern is null at the tip of the wire so make sure that you keep the antenna perpendicular to the source of the radio signals

Thanks
Helpful 5 Not Helpful 0
Make sure the wire is perpendicular to the ground plane

Thanks
Helpful 2 Not Helpful 1
The Antenna has a pretty much circular pattern when viewed from the top, so it should pick up your signal no matter where you decide to place it.

Thanks
Helpful 1 Not Helpful 1

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

If you short the GND and the signal wire you'll be in trouble.

Thanks
Helpful 12 Not Helpful 5
Don't let it get wet, as this frequency is not "friendly" to water.

Thanks
Helpful 5 Not Helpful 9

Things You'll Need

Coaxial Cable
Copper Plate

Log in

How to Design a Simple Antenna

Steps

Choose a frequency.

Get a conductor.

Determine the wire length.

Cut the wire.

Form a ground-plane.

Drill a hole.

Pare the coaxial cable.

Feed the cable through.

Reveal the signal conductor.

Solder the wire.

Community Q&A

Video

Tips

Warnings

Things You'll Need

You Might Also Like

About This Article

Is this article up to date?

About This Article

Quizzes

You Might Also Like

Featured Articles

Trending Articles

Featured Articles

Featured Articles

Watch Articles

Trending Articles

Quizzes

Explore Categories