Download Article
A guide to safely discharging a CRT monitor without getting shocked
Download Article
If you need to make internal adjustments to a CRT monitor, it's safe to discharge it first. A CRT monitor has a high-voltage anode inside it, which can carry a charge of up to 25,000 volts. If you don't discharge the monitor (and if you do, but improperly,) you can get electrocuted. Know what you're doing before you obey this article!
Steps
Download Article
-
Unplug the monitor. -
Leave it alone for a few hours. If you can afford to waste a lot of time, twenty-four hours would be better.Advertisement -
Wear rubber-soled shoes (no steel toes) and safety goggles. Take off all your jewelry, especially rings and watches. You don't want to be grounded in any way. -
Find a heavy flat-bladed screwdriver with good insulation. A Swiss Army knife is not acceptable. -
Find a heavy-gauge wire with alligator clips on the end. -
Take the monitor's case off -- and don't forget where the screws go in. This could lead to embarrassment. -
Attach one alligator clamp to an unpainted portion of the metal frame. -
Attach the other alligator clip to the screwdriver's metal shaft. -
Make sure that neither you or the screwdriver are in contact with anything metal. -
The anode is a wire covered by a suction cup. Slide the screwdriver blade under the suction cup until you hear a loud pop and see a blue flash. -
Wait for about 30 minutes and repeat.
Advertisement
Community Q&A
Search
-
QuestionI directly removed the suction cup, and I did the wikiHow process with a screwdriver and copper wire, but I have not heard any pop up sound. Does that mean it's discharged completely?Community AnswerIt means that the discharge is complete. If it gave the pop up sound it might need a new replacement part.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Alternative Solution
- Unplug the monitor. (As said above)
- Carefully unscrew housing and remove.
- Wear electric resistant gloves. (Non-conductive material)
- Prepare with a flat-tip screwdriver and a jumper cable with alligator clip ends.
- Begin by clipping one end of the jumper cable to the screwdriver.
- Follow up by clipping the other end to 'ground'. (Ground is usually a large metal area, usually in which the CRT monitor is mounted on)
- Slide the flat-tip screwdriver under the anode suction cup. (Aim towards the middle, where the anode actually is)
- You may or may not have heard a sign of success, (Such as noted above) but you have completed the task successfully. Always wear protective gear during the process!
Tips
- The loud pop will bring anyone within hearing distance running. Reassure them.Thanks
- If you are jittery about electricity, do not carry out this procedure. You are more likely to make a mistake if you are nervous. Take it to a professional.Thanks
- Minor amounts of static electricity may continue to collect after the discharge: if you are not servicing this circuit immediately you must repeat the discharge procedure before working on the circuit. Also, briefly discharge or short especially the large capacitors to avoid similar shock surprises.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- You don't want to be grounded. Make sure that, during the entire procedure, you are not accidentally allowing yourself to be grounded.Thanks
- Protect your eyes in case the CRT implodes (not likely.)Thanks
- If you have any doubts whatsoever, DO NOT carry out this procedure. If you mess up, you could be shocked, or even electrocuted. Ask for professional assistance.Thanks
Advertisement
Things You'll Need
- CRT Monitor
- Flat-bladed screwdriver
- Heavy-gauge wire with alligator clips
- Safety goggles
- Rubber-soled shoes
- Nerves of steel.
References
- Myers, Michael and Jernigan, Scott. "A+ Certification Exam Guide, 5th Edition." Emeryville, California: McGraw Hill/Osborne. 2003. p. 846
About This Article
Thanks to all authors for creating a page that has been read 129,914 times.
Advertisement
