Download Article
Download Article
If your floors are uneven, a latex self-leveling compound (sometimes called latex screed or mortar) can help smooth over areas that are not level. This is usually done before painting, tiling, or carpeting a subfloor. Before you begin, you will need to identify where your floor dips or rises. Clean the floor before applying a thin layer of latex mortar to the floor. Latex only takes a day to dry, so you can continue with your project the very next day.
Steps
-
Remove any carpeting or tile. If you already have carpet or tile on your floor, you will need to remove it before you can examine the subfloor. If the floor is concrete, clear away any furniture or rugs on top of it. [1] X Research source
- For carpet, you can cut off pieces with a utility knife and pull it up using a pry bar.
- To remove tile, cut the grout with a utility knife and lift up each piece with a chisel.
-
Place a level on various areas of the floor. A level contains a liquid with an air pocket. Place the level in areas where you suspect the floor is uneven. If the air bubble settles in the center, it is even. If it slides to one side, it is uneven. [2] X Research source
- Latex screed works best on dips that are no more than 2 inches (5.1 cm) lower than the floor.
Advertisement -
Set a straightedge across the floor. If the straightedge tips to one side, your floor may have a raised bump in it. If you notice a gap between the straightedge and the floor, your floor is dipping in that area. [3] X Research source
-
Run a string across the ground. Tape or tie the string to one side of the room. You can also have a partner hold it. Walk across the room, and hold the string tightly so that it is taut. It should just barely skim across the top of the floor. Look for any places where the floor dips below the string or pushes it up. [4] X Research source
Advertisement
-
Scrape off any residue. The floor will need to be completely clean before you begin. If there is any glue, mortar, or residue left over from taking out the tile or carpet, remove it with a scraper. Sweep up any leftover debris afterwards. [5] X Research source
-
Vacuum up the dust. After all of the visible debris is gone, vacuum to remove any dust or dirt. If vacuuming doesn’t remove all of the dust, try taking a wet sponge and washing it away. Let it dry before you continue. [6] X Research source
-
Attach a metal lath to a wooden floor. If you have any type of wooden subfloor, you cannot use latex self-leveling compound directly on it. Instead, roll out and staple a metal lath over the entire floor first. [7] X Research source
- A metal lath is a net of enmeshed metal. You can buy it at hardware stores.
- Latex self-leveling compound can be applied directly to concrete, cement board, or HardieBacker floors.
Advertisement
-
Mix the compound in a five-gallon bucket. Most compounds will have two components: a liquid latex solution and a bag of dry mortar mix. Prepare the compound right before you are ready to cover the floor. [8] X Research source
- How much you mix will depend on the size of the room and the height of the dips. Your self-leveling compound should have instructions on the side of its label for the amount you will need.
- You can buy the self-leveling compound at hardware stores or online. Some latex solutions come premixed. These will be sold in a bottle.
- The self-leveling compound will be spreadable for about an hour after mixing.
-
Start pouring the compound in the corner farthest away from the door. Work your way towards the door so that you do not have step over the wet latex when you are done. The latex will settle in the dips of the room, creating a smooth surface. [9] X Research source
-
Smooth out the latex with a screed. A screed is a long, flat tool used to make mortar even. After you pour the self-leveling compound, scrape the screed over the latex to spread it evenly over the floor. Make sure to fill in any dips in the floor. [10] X Research source
- You can also use a paint roller or finishing trowel if you don’t have a screed.
-
Let the latex dry for 24 hours. Test that it is completely dry with a gloved finger or a dry stick. Give it another day if it isn’t dry. If it is dry, you can continue with your project by applying tile, vinyl, paint, or carpeting on top of the floor. [11] X Research source
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Try wearing shoes with spikes on the bottom. These allow you to walk on top of the latex without disrupting the surface. [12] X Research sourceThanks
- While you can do this alone, it is easier to do it with a partner.Thanks
- If you have underfloor heating, check your brand of latex compound to make sure it is compatible with heating.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
- ↑ http://cabindiy.com/how-to/level-a-floor/
- ↑ http://www.oneprojectcloser.com/how-to-even-a-floor-in-preparation-for-tile/
- ↑ http://www.oneprojectcloser.com/how-to-even-a-floor-in-preparation-for-tile/
- ↑ http://www.oneprojectcloser.com/how-to-even-a-floor-in-preparation-for-tile/
- ↑ http://cabindiy.com/how-to/level-a-floor/
- ↑ http://www.diydoctor.org.uk/projects/levelling-concrete-floors.htm
- ↑ http://www.tilecleaning.org/self-leveling-compound.htm
- ↑ http://www.oneprojectcloser.com/how-to-even-a-floor-in-preparation-for-tile/
- ↑ http://www.tilecleaning.org/self-leveling-compound.htm
About This Article
Thanks to all authors for creating a page that has been read 54,006 times.
Advertisement