PDF download Download Article
Make cool custom cheer bows with or without glue
PDF download Download Article

Are you looking for a simple guide to making colorful cheer bows or your squad? While you can buy cheer bows, they’re quick, easy, and fun to make yourself. Plus, when you DIY your cheer bows, you can customize them to look exactly how you want. To help you get started, we’ve created step-by-step instructions to walk you through how to make cheer bows with and without using hot glue…with zero sewing! You’ll also see a few tips and a list of ideas to help you design really unique and eye-catching cheer bows.

Easy Steps to Make Your Own Cheer Bows

  • Fold a 26” to 32” length of 3” wide grosgrain ribbon into the shape of an awareness ribbon and then gather the center of all 3 layers to make the bow.
  • Loop an elastic hairband onto a zip tie, then secure the center of the bow with the zip tie.
  • Wrap the cable tie with a smaller piece of ribbon, securing it with glue or double-sided tape to disguise it.
Section 1 of 2:

Making a DIY Cheer Bow

PDF download Download Article
  1. Cut a 26” to 32” length of 3” grosgrain ribbon . This is the ribbon you use to make the bow. Choose a longer ribbon to make your cheer bow larger.
  2. Watermark wikiHow to Make a Cheer Bow
    Lay the length of ribbon flat on your workspace and mark the midpoint by measuring it and using a fabric marker or by folding the ribbon in half and lightly creasing along the fold. Fold the left end of the ribbon to the right in a shallow diagonal. Then fold the right side diagonally so it crosses the first end.
    Advertisement
  3. Watermark wikiHow to Make a Cheer Bow
    Shift the crossed section of the ribbon to the midpoint you marked in an earlier step. Use your thumb and forefinger to bunch all three layers of ribbon together.
    • When bunching the ribbon to create the bow, you can make it look neater by creating 3-4 small folds. [1]
  4. Watermark wikiHow to Make a Cheer Bow
    While holding the bunched section, wrap a 4” cable tie around it. Slip a hair tie through the zip tie, and pull the zip tie just tight enough to secure the bow. [2]
    • Adjust the bow so it’s even, and move the elastic hairband to the back near when the zip tie fastens. [3]
    • Pull the zip tie tight, and then use your scissors to cut the zip tie’s excess tail flush with its fastener.
    • Alternatively, secure the bow with the zip tie, then hot glue a hair tie to the zip tie on the back of the bow. Press one side of the elastic hairband into the glue and hold until set. [4]
    • Be careful to allow the glue to cool slightly before attaching the elastic hairband. Hot glue can burn your skin if you touch it before it cools. Remove any excess hot glue by lightly scratching it off or loosening it with rubbing alcohol.
  5. Watermark wikiHow to Make a Cheer Bow
    Hide the cable tie with a piece of narrow grosgrain ribbon . Place a dab of hot glue on the center of the back of the bow. Press the end of your narrower ribbon into the glue and allow it to set. Then, wrap the ribbon around the center of the bow and press into the glue on the back. [5]
    • Alternatively, attach the narrow ribbon around the bow with ¼” double-sided tape . Remove the backing strip from one side of the tape and stick it to the back of the ribbon. Trim if necessary, and then remove the backing strip from the other side of the tape. Wrap the ribbon with the double-sided tape down around the cable tie securing the middle of the bow. Trim off any ribbon that extends beyond the center of the bow.
    • To make the bow look like it was tied, cut a 3” to 4” length of your narrower ribbon. This works best with ½” to ⅞” widths. Tie a knot and pull tight. Trim the excess ribbon so there are about two inches on each side of the knot. Glue the knot to the front of your cheer bow, then wrap the ends around to the back and glue them together covering the glued section of the elastic hairband. Trim any excess ribbon.
  6. Watermark wikiHow to Make a Cheer Bow
    Use your scissors to cut the end of each of the bow’s tails on a diagonal or in a chevron (or fishtail) shape.
    • You can cut an even chevron shape by folding the very end of the tail in half lengthwise and then cutting from the fold to the edge in a downward diagonal.
    • After cutting, use your lighter to skim the flame quickly along the cut edge of the ribbon to seal it. [6] Make sure you move very quickly and only touch the flame to the very edge of the ribbon, or it could melt.
  7. Watermark wikiHow to Make a Cheer Bow
    The bow’s loops may have flattened while you were finishing up. You can make them look fuller by placing your fingers inside each loop and fluffing it out.
  8. Use spray starch , hairspray, or Aleen’s Stiffen Quik .
    • If you use spray starch, you must spray and iron your ribbon before making the bow.
  9. Advertisement
Section 2 of 2:

Ideas for Cheerbow Designs

PDF download Download Article
  1. This can help you bring more color to your cheer bow designs. It also gives you a chance to incorporate your school colors in fun and interesting ways.
  2. Watermark wikiHow to Make a Cheer Bow
    You can use rhinestones to create a pattern across the ribbon or line the edges with sequins…or both! There’s an almost endless variety of items you can use to bring more glitz to your cheer bows.
  3. Use iron-on patches and decals to add your name, school initials, or school mascot to your cheer bow. You can also create your own patches for more customization options.
  4. Create a fuller cheer bow by hot gluing a variety of ribbons to the back. Loop each ribbon and tack it to the back of the bow with a small dab of glue. Make sure you arrange the ribbons with the loops pointing out from the center so they appear to be tied in with the bow.
  5. Advertisement

Expert Q&A

Ask a Question
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Thanks for submitting a tip for review!

      Warnings

      • Many stiffening agents are flammable, so make sure to seal the edges of the ribbon before you use these products or skip that step.
      • Depending on the type of hot glue gun you own, it can reach temperatures up to 380 degrees. [7] Use caution when handling the gun and the hot glue.
      Advertisement

      Things You’ll Need

      About This Article

      Thanks to all authors for creating a page that has been read 1,722 times.

      Did this article help you?

      Advertisement