Download Article
Download Article
Spurs can help improve communication between a rider and a mount. If you’ve selected a shiny new pair of spurs, you may be wondering how to attach them to your favorite cowboy boots. The process is quite simple and should only take a few minutes. Once you understand and assemble your new spurs , you’ll have them on your boots and be riding in no time.
Steps
-
Locate the spur ledge on the back of your cowboy boot. The spur ledge is the protruding part of the boot heel that creates a small shelf where the spur heel band will rest. [1] X Research source
- The spur ledge is a very slight ledge, just large enough so that the heel band doesn’t slip down the boot.
- All cowboy style boots should have a spur ledge. If you are not sure about your boots, take them with you when you go to purchase your spurs.
- Jump to info on assembling or attaching the spurs if you've already set them up.
-
Find the heel band portion of the spur. The heel band is the U-shaped piece of metal that wraps around the boot’s heel and is held on by a strap. The heel band may have buttons where the straps will attach or bars for threading straps to attach. [2] X Research source
- You will need a heel band that is approximately the same size as the heel portion of your cowboy boot.
Advertisement -
Choose 1 long strap if the heel band has bars. If the heel band has bars on both sides, you will need 1 long strap with a buckle on one end to attach the heel band to the boot. [3] X Research source
- Take a look at your strap to see if it has a decoration, metal work, or fancy design on one side. You want the decorative side to always be visible on the outside of your boot.
-
Get 2 small straps if the heel band has buttons. If the heel band has buttons on both sides, you will need 2 smaller straps with buttonholes. These will ultimately buckle together after being attached to both sides of the heel band. [4] X Research source
- Take a look at your straps to see if either of them have a decorative, scalloped, or fancy side. You want the decorative side to always be visible on the outside of your boot.
-
Look for the shank on the spur. The shank is a small metal piece that extends from the middle of the heel band. The shank should point down once the spur is in place on the boot. [5] X Research source
-
Spot the rowel on the back of the spur. The rowel is the rotating disk with blunt points attached to the shank on the heel band. This is the most important part of the spur because it is the part you will use to nudge your horse in the side to communicate your intentions with him. [6] X Research source
- Exercise caution when handling the rowel so that you don’t accidentally cut yourself. Most aren’t incredibly sharp but could still cause pain if grabbed too tightly.
Advertisement
-
Gather all the pieces needed to assemble your spur. You’ll need to grab your boots, heel band (with rowel attached), and the straps you will be using. This is a perfect time to position any decorative strap sides where you want them before attaching them to the heel band.
-
Attach button straps onto heel bands with buttons. For this type of heel band, you will need 2 small straps with buttonholes. [7] X Research source The straps will be attached on either side of the heel band and then buckled across the boot later.
- Hold the heel band in your hand with the shank facing down.
- Start with one side of the heel band and place the first strap with the buttonhole over the heel band button.
- Spread the buttonhole apart to push the button through the hole.
- Rotate the strap around the button until it lays down flat.
- Repeat with the other side of the heel band and attach the second strap.
-
Thread straps into a heel band with bars. For this type of heel band, you will need 1 longer strap with a buckle. [8] X Research source With 1 long strap you will thread it through both sides of the heel band and buckle it across the boot later.
- Hold the heel band in your hand with the shank facing down.
- Begin threading the strap from the inside of the outward facing heel band bar.
- Thread the strap through the bars. The buckle should end up on the outside of your boot.
- Leave some strap to go under the boot and then thread the same strap into the other side of the heel band through the bars.
Advertisement
-
Fit the heel band to the spur ledge of your boot. The heel band should rest on the spur ledge with the shank facing down. The fit should not be too tight or too loose. There should be a little bit of movement for the spur to fit correctly. If the fit is off just slightly, you may be able to gently pull it apart to loosen it or squeeze a bit to tighten it. [9] X Research source
-
Attach the spur to your boot by buckling the straps. Once the heel band is fitted in place at the back of your boot, buckle the strap or straps together over the boot to create a snug fit. [10] X Research source
- Put the buckles on the outside of the boots. If the buckles are facing the inside of the boots, they will rub together at your ankles and be uncomfortable.
-
Adjust the strap so that the spur fits snugly onto the boot. If the spur is too tight or too loose once buckled onto your boot, you may need to let some strap in or out of the buckle to adjust the fit. [11] X Research source
- Start by unbuckling the strap. Next, adjust the length of the strap as needed to ensure a good fit. Finish up by re-buckling the strap.
Advertisement
Community Q&A
Search
-
QuestionCould I wear my spurs to school? (I'm in middle school)Community AnswerThat's a great idea! As long as it follows your school's dress code and you're fine with the possibility of a few stares (or high-fives!)
-
QuestionMy spurs have a double heel chines. Do they go in front of the heel or one on each of the heel?Community AnswerThe spurs on your boots have one on each heel. With two, the shoes would be too heavy to walk in and you would seriously hurt your cattle whilst riding.
-
QuestionWhat do I do if my shoes do not have ledges? Can I get a type of spur that doesn't need them?Community AnswerYes, you can. they are called portable spurs. However, they may not have any portable spurs locally, you might need to purchase them online.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If you are having trouble attaching the spur to your boot while you are wearing the boots, try fitting the spur to the boot and buckling them in place before slipping the boot onto your foot.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
References
- ↑ https://www.texasmonthly.com/the-culture/how-to-wear-spurs/
- ↑ https://www.youtube.com/watch?v=ZQTxlJsT2E8
- ↑ https://www.youtube.com/watch?v=ZQTxlJsT2E8
- ↑ https://www.youtube.com/watch?v=z0gmf4xQV8A
- ↑ https://www.texasmonthly.com/the-culture/how-to-wear-spurs/
- ↑ http://www.cowboyshowcase.com/spurs.html
- ↑ https://www.youtube.com/watch?v=z0gmf4xQV8A
- ↑ https://www.youtube.com/watch?v=ZQTxlJsT2E8
- ↑ https://www.youtube.com/watch?v=z0gmf4xQV8A
About This Article
Thanks to all authors for creating a page that has been read 93,856 times.
Advertisement