Download Article
Download Article
Concrete steps are exposed to the elements every day. After time, the steps can crack or begin to break apart. Cracked steps pose a potential safety risk to people entering or leaving your home and must be repaired. Use these instructions to repair concrete steps.
Steps
-
Clean the damaged portion of the concrete step. Remove all loose gravel, sand, dirt, and cement with a clean, stiff wire brush. You can also tap lightly with a hammer or use a hammer and chisel. [1] X Research source
- If the day is going to be hot, work in the morning, and then moisten the cement throughout the day.
-
Make a form. Screw 2 short pieces of 1 inch by 6 inch (2.54 cm by 15.24 cm) lumber together at a 90-degree angle to form an "L" shape. [2] X Research source
- The form can also be held together using several long pieces of duct tape.
Advertisement -
Align the wood form. Place the wood form against the damaged corner of the concrete step so it is flush with the top of the step. Tape the form to the step firmly with duct tape. [3] X Research source
-
Lubricate the form. Spray a coat of cooking oil spray on the inside of the wood form to prevent the wood from sticking to the new concrete.
-
Apply bonding liquid. Use a paint brush to apply a thick coat of latex bonding liquid on the damaged portion of the concrete step were you will be applying the new concrete. [4] X Research source
-
Prepare quick-setting cement. Mix a small amount of quick-setting cement in a plastic bucket according to the instructions on the packaging. Make sure to add enough water, otherwise you won't be able to mix it properly. Do not use pre-mixed vinyl cement repair because it shrinks and will not hold weight. These vinyl fillers are best used to fill holes in stucco walls where no one is walking over them. "Cement-all", that is $22 per bag, does not need a bonding agent, and can be driven over in 60 minutes with an automobile.
- When you are mixing cement, wear safety gloves, a safety mask, and clothes that cover your skin (like jeans).
-
Dampen the area. Moisten the area where you are going to be adding the new cement so that the existing concrete will not draw the moisture out of the wet cement, making it less likely to harden properly.
-
Apply the cement. Use a pointed trowel to scoop the cement onto the damaged portion of the step and press it into the wood form. Overfill the wood form slightly.
-
Smooth the newly laid cement. Use the flat side of the trowel to smooth the cement so it is flush with the remaining portion of the step. Don't be afraid to apply pressure. Pressure will fill holes and make it more level.
-
Allow the concrete to dry overnight.
-
Remove the duct tape and the wood form.
-
Keep the cement moist. Use a spray bottle to moisten the new concrete patch 2 or 3 times a day for 3 days. Then moisten the patch twice daily for a week.
- This is needed to make the cement cure slower. If it gets dry too fast, it is more likely to crack.
Advertisement
Community Q&A
Search
-
QuestionDoes an external repair need to be covered to protect it from the rain?Community AnswerYes, cover the cement with plastic or plywood. If you use fast drying cement, it will not need to be covered because most fast drying cements cure within 1 hour.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- The wet cement mixture should hold together in a clump when you squeeze a handful. If the cement mixture crumbles, add more water. If it drips, add more dry concrete mix.Thanks
- You may need to remove any additional loose cement in the damaged area using a hand sledgehammer. Unless all the damaged cement is removed, you'll probably need to redo the repair as the new patch may be unstable.Thanks
- It is important to keep the new cement patch moist for at least the first week after making the repair. Maintaining a sufficient moisture level is necessary for the new concrete to cure and harden properly.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Things You'll Need
- Wire brush
- 1-inch by 6-inch (2.54 cm by 15.24 cm) lumber
- Duct tape
- Drill and screws (optional)
- Cooking oil spray
- Latex bonding liquid
- Quick-setting cement
- Plastic bucket
- Plastic spray bottle
- Hand sledgehammer, if needed
- Trowel
References
- ↑ https://www.todayshomeowner.com/video/how-to-repair-and-resurface-concrete-steps/
- ↑ https://www.todayshomeowner.com/video/how-to-repair-and-resurface-concrete-steps/
- ↑ https://www.dummies.com/home-garden/exteriors/how-to-repair-broken-concrete-step-corners/
- ↑ https://www.dummies.com/home-garden/exteriors/how-to-repair-broken-concrete-step-corners/
- https://www.thisoldhouse.com/stairs/21019223/fixing-chipped-concrete-steps
About This Article
Thanks to all authors for creating a page that has been read 96,994 times.
Advertisement