Download Article
Download Article
Here is a step by step tutorial on how to replace a dryer belt on a Whirlpool dryer. This can be a relatively simple repair that can save you time and money since you won't have to call in an appliance service professional for a common problem. However, if after reading this guide, it seems like more than you can handle, take the safest route and call a professional appliance service company.
Get Product Support Solve Any Problem
Try Asking:
We’re sorry we don’t have the product, brand, or model you are looking for. Please enter its name below so that we can add support for it.
Thank you! We’ll review your request and add support for this product as soon as possible. In the meantime, you can ask more questions about the products we currently support.
Steps
Download Article
-
Start by removing the lint filter. Using your 5/16th screwdriver, remove the two screws under the lint filter. [1] X Research source -
Next, take the putty knife and place it in the opening between the top of the dryer and the front of the dryer. Pop up the top of the dryer and repeat on the other side. [2] X Research sourceAdvertisement -
Flip the top out of the way. There will be two screws in each upper corner of the inside of the dryer. Remove both of these and put screws in container for later. -
The front of the dryer will now be released. Pull the top away from the cabinet and then lift it up. Swing the front to the side and place it out of the way. You may need to disconnect the lid switch wires if they are not long enough to allow this. [3] X Research source -
Release the belt from around the drum. [4] X Research source To do this, the belt will be looped under the idler pulley and then attached to the motor. Reach under the drum and unhook the belt from around the motor.- The pulley may be just a spring part with a half circle the belt runs around, with no moving part.
-
To attach the new belt, begin by placing the belt, with the groove side down and lined up with the markings around the drum. Then loop the belt under the idler pulley (that has a moving wheel) and attach it back to the motor. The idler pulley should apply tension to the belt. You may need an extra hand for this step since the dryer drum can sag down and make it difficult to reach the motor. [5] X Research source -
Make sure the rear felt on the back end of the drum isn't folded under. If it has, use a screwdriver to pop the felt out while spinning the drum with your hand. -
Reassemble the dryer. Make sure the small tabs on the bottom of the dryer match up with the small holes on the dryer front. Replace screws and lint trap.
Advertisement
Community Q&A
Search
-
QuestionWhat happens if the wheel is missing from the idler pulley?Community AnswerMany models did not have idler wheels, but instead just a semi-circle made of metal.
-
QuestionMy "small tabs" on the bottom of the front casing broke. Is there a substitute or another way to hold it in place? It's all fixed but the front casing is lopsided and I'm unsure if this will hurt it. What can I do?Community AnswerThe same thing happened to me. I drilled one hole on each side of that, below where the tabs were, and used a couple of drywall screws to hold it in place. That was several years ago and it has been working fine ever since.
-
QuestionWhere can I get a new dryer belt?Community AnswerAppliance stores and larger hardware stores will carry replacement belts. Take your old belt with you and they can help get you the same size. If you don't have any luck locally, you can find a replacement belt for your model on Whirlpool's website, eBay or Amazon.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- When reassembling the door panel make sure the slotted tabs on the bottom of the door panel slip onto the screws on both sides of the frame near the bottom panel.Thanks
- The inside of the dryer can accumulate a lot of dirt so it's a good idea to vacuum the inside while you have the dryer apart.Thanks
- Place the belt around the drum first. Use a small can to prop up the drum if working alone. You will have to reach between the drum and front to remove the can before closing the front completely.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Secure the top so it does not fall while working on the belt/drum assembly.Thanks
- Make sure your dryer is unplugged and completely powered down before beginning any repair.Thanks
Advertisement
Things You'll Need
- 5/16th nut driver or socket
- Putty knife
- Container for screws
- Phillips screwdriver
- lightweight gloves to protect fingers when placing belt (under tension)onto motor shaft.
Expert Interview
Thanks for reading our article! If you’d like to learn more about appliance repair, check out our in-depth interview with Trevor Storey .
References
- ↑ https://www.youtube.com/watch?v=SyLkMKr1YPg&app=desktop
- ↑ https://www.youtube.com/watch?v=SyLkMKr1YPg&app=desktop
- ↑ https://www.partselect.com/JustForFun/How-To-Replace-A-Dryer-Belt-On-Whirlpool-Models.htm
- ↑ https://www.partselect.com/JustForFun/How-To-Replace-A-Dryer-Belt-On-Whirlpool-Models.htm
- ↑ https://www.youtube.com/watch?v=GzYmoS9brMY
About This Article
Thanks to all authors for creating a page that has been read 261,801 times.
Reader Success Stories
- "This saved me a lot of unnecessary taking apart of other screws. I have worked on dryers before, but far and few between; I forget from one time to the next how to do it." ..." more
Advertisement
"This saved me a lot of unnecessary taking apart of other screws. I have worked on dryers before, but far and few between; I forget from one time to the next how to do it."
..."
more
"The instructions were clear and precise. I appreciated the instructions."
"Clear, concise and made it an easy DIY. Well done!"
"Great step-by-step instructions."
