How to Rig a Laser Sailboat

PDF download Download Article
PDF download Download Article

This is a step by step instruction on how to rig the original laser.

Steps

PDF download Download Article
  1. You should have the boat itself (the hull), the dagger board, the rudder and tiller, your mainsheet, both mast pieces, boom, boom bang and sail in one place.
  2. The bottom of the top half just slides into the top of the bottom half. There are no locks, or anything, it should just fit snugly. [1]
    Advertisement
  3. There will be a pocket along one side of the sail to slide over the mast. [2]
  4. [3]
  5. This is the hardest part of the entire rigging process, so be careful, no-one likes a broken mast or hull. You stand up the mast, make sure it's right next to the bow of the laser, and pick it straight up off the ground, and put it into the mast step (the hole at the front of your laser). A way to make this easier is to grab the mast around the middle, then walk forward thereby pushing the sail up. While walking you should also move your top hand up to have better control of the mast.
    • The sail should now be flapping in the wind.
  6. Hold it in there, as it will fall off without any other support.
  7. Grab the outhaul (the line on the very end of the sail), and put it through the eye at the end of the boom. Now run the line down the boom, and cleat it off. [4]
    • If you have cleated the outhaul properly, the boom should now stay up on its own.
  8. Attach the clew-tie-down (a small line that wraps around the ring the outhaul is attached to) and wrap it around the boom and tie it so that the clew is as close to the boom as it can be while still being able to slide back and forth along the boom. [5]
  9. Supposing it is already rigged itself, you only have to attach it to the bottom of the mast, then slide it into the little metal clip on the bottom of the boom. Now pull down on the hanging line, and then pull straight up to cleat it. [6]
  10. Take one end of it, go to the end of the boom, and tie it around the eye on the bottom of the pulley there. Do not put it through the pulley itself; you're going to need that pulley in a moment. Now that it's tied off, find the other end of your line, and run it through the traveler on the stern of the boat. Then run it back up, through the pulley on the end up the boom, then forward across the bottom of the boom, through that metal loop, through the next pulley, and then down through the main block at the front of the cockpit. Make sure that your main block clicks when you pull the mainsheet through it - if it doesn't, you have to run the mainsheet through the other side of the main block. Then tie a knot in the very end of the mainsheet, so the line can't run back through the main block when you are sailing or if you capsize. [7]
  11. Then attach the rudder, tiller and daggerboard. Slide the rudder pins into the eyes on the backside of the laser, and make sure that the clip is holding it down. [8]
    • Test it by pulling up on the rudder. Then put on the tiller by sliding it into the space on the top of the rudder. Once it's in, insert the pin to hold it there.
    • Tie the dagger board with a long loop of elastic to the eye at the very front of the boat.
    • Verify the elastic creates enough friction that the daggerboard will stay up or down (even when you invert the boat).
  12. The last thing you need to do, just before you start sailing, is tie down the rudder. There is a tiny string, found anywhere around the rudder and tiller, that you have to pull on to bring down the rudder. Once it's down, tie off the string on the cleat that is on the side of your tiller, and you're set to sail!
    13. Advertisement


Community Q&A

Search
Add New Question
  • Question
    What does "flake" mean?
    Aloha27
    Community Answer
    "Flake" means to carefully lay out a line so it will not kink or jam when it goes through a sheave (pulley).
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 4 Helpful 6
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      • If this is a new boat, rig it entirely, on land, and test out all the parts. Pull on the mainsheet and such, in order to make sure nothing breaks. This way, you're not stuck on the water when a part of the boat fails.
        Thanks
        Helpful 0 Not Helpful 0
      • Flake the main sheet twice, once on hull then lastly inside cockpit so the bitter end is on the bottom..also a weather cane clipped on mast directly across from boom is helpful as well as tell-tales (and a whistle in your life vest and a helmet on your head).
        Thanks
        Helpful 0 Not Helpful 0
      • When rigging the boat, make sure it is pointed into the wind
        Thanks
        Helpful 0 Not Helpful 0
      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      Things You'll Need

      • The boat itself (the hull)
      • the dagger board and a piece of elastic
      • the rudder and tiller
      • your mainsheet
      • both mast pieces
      • boom
      • boom vang
      • sail
      • battens
      • one hull plug

      You Might Also Like

      How to
      Back a Trailer
      How to
      Read a Nautical Chart
      Navigating by the Stars: Find North, South, & More
      How to
      Sail a Boat
      How to
      Tie a Boat to a Dock
      How to
      Shrink Wrap a Boat
      How to
      Tie Fenders on a Boat
      How to
      Run a Boat Motor Out of Water
      How to
      Start an Outboard Motor
      Your Ultimate Guide to Boat Transoms
      How to
      Start Sailing
      How to
      Store a Kayak
      How to
      Maintain an Outboard Motor
      How to
      Transfer a Boat Title
      Advertisement

      References

      1. ↑ https://www.youtube.com/watch?v=rKlIYWfhx10
      2. ↑ https://www.youtube.com/watch?v=R3HsMXwGUNs
      3. ↑ https://lasersailingtips.com/rigging-and-launching/
      4. ↑ http://marinaaquaticcenter.org/sailing/PDFs/Laser%20Rigging.pdf
      5. ↑ http://marinaaquaticcenter.org/sailing/PDFs/Laser%20Rigging.pdf
      6. ↑ http://marinaaquaticcenter.org/sailing/PDFs/Laser%20Rigging.pdf
      7. ↑ http://marinaaquaticcenter.org/sailing/PDFs/Laser%20Rigging.pdf
      8. ↑ http://marinaaquaticcenter.org/sailing/PDFs/Laser%20Rigging.pdf

      About This Article

      Thanks to all authors for creating a page that has been read 153,690 times.

      Did this article help you?

      Advertisement