Download Article
Download Article
Starting a snowblower involves a few steps to inspect your machine and make sure it's in running condition. Then, prime your engine so it’s ready to ignite. Finally, use the starter rope or electric starter (depending on your model) to get your snowblower up and running.
Steps
-
Check the oil level. Before starting your snowblower, you’ll want to make sure that the oil level is at the “full” mark. If not, top off as needed, according to the manufacturer’s instructions.
-
Fuel up. Your snowblower’s manufacturer will recommend a specific fuel type/grade. You’ll want to have plenty of fuel before you begin. Make sure it's fresh, especially if you haven't fired up your snowblower in a while. [1] X Research source
- Drain your gas if your snowblower has sat longer than a month with ethanol fuel in it. Ethanol fuel can deteriorate over time, and bad fuel can cause engine problems. [2] X Research source
Advertisement -
Set the drive control to neutral. For safety reasons, you’ll want all drive controls set to “off” before starting your snowblower. Keeping your snowblower in neutral will prevent unintended activity once the machine starts.
Advertisement
-
Set the choke to “full.” This is important for a cold start, so the fuel will mix properly with air and the engine will fire correctly. However, if you used your snowblower very recently (within five minutes), set the choke to the warm start setting, or about halfway.
-
Increase the throttle. Turn it to the “fast” setting. Many models will identify this with a rabbit symbol. You should always start your snowblower on this setting. [3] X Research source
-
Turn on the fuel. Your snowblower will have a fuel shutoff valve. To start using your snow blower, you will have to turn this to the “on” position. If you are unsure of the valve’s location, check the manual. [4] X Research source
- Always make sure to turn the fuel shutoff valve back to “off” when you are done with your snowblower. This will reduce the risk that fuel will leak.
-
Hit the ignition switch. Usually, this control is a simple up/down switch, much like a light switch. Turn it to the “on” or “run” position. [5] X Research source
-
Insert the key, if applicable. Some snow blowers include a key as a safety feature. These models won’t run unless the key is inserted. [6] X Research source
- If you need to quickly stop your snow blower while operating it, just remove the key.
-
Push the primer bulb. This is a bubble-like switch that helps circulate fuel. Pushing it a few times should be enough. Try twice if the temperature is above 15 degrees Fahrenheit (-9 Celsius), or four times if the temperature is below this. [7] X Research source
- Don’t push the primer for a warm start (if you used the snowblower less than five minutes prior to starting again).
Advertisement
-
Pull the starter rope, if your model has one. Grasp the starter rope by its handle. Pull slowly until you feel it “catch” some resistance. Then quickly and smoothly pull upward to start the engine. [8] X Research source
-
Plug in the snowblower’s power cord if applicable. If your model has an electric starter, take the three-pronged cord and plug the other end into an outlet. The outlet must be the same voltage as your snow blower. [9] X Research source
- Read your model’s instruction manual if you are unsure of the voltage level.
-
Press the start button, if your model has an electric start. Push the button in short cycles of only five seconds until the engine fires and stays running. Overtaxing the starter can damage it.
- Disconnect from the power source once your snowblower is running.
-
Turn the choke switch off when you're ready to use the snowblower. Let your snowblower run for a few minutes to warm up. Then, turn the choke to the “off” or “run” setting. Your snowblower is now ready to use. [10] X Research source
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- If you run into problems starting the snow blower, talk to a dealer or consult the manual. Common problems include faulty spark plugs and improper mixing of fuel and air. [11] X Research sourceThanks
- Always read the manufacturer’s manual for complete instructions and safety information.Thanks
- Store your snow blower properly, according to the manufacturer’s instructions. This will make sure the tool is ready to go when you need it.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
References
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
- ↑ http://michiganradio.org/post/you-start-snow-blower-read
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
- ↑ https://www.toro.com/en/customer-support/help-center-snow
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
- ↑ https://www.snowblowersatjacks.com/starting-your-snow-blower-the-ultimate-cheat-sheet.aspx
About This Article
Article Summary
X
To start a snowblower, set the choke to “full” and increase the throttle to the “fast” setting. Next, turn the fuel shutoff valve to the "on" position and hit the ignition switch, which typically looks like a light switch. If your snowblower has a key, insert it now. Then, push the primer bulb a few times to circulate the fuel. If your model has a starter rope, pull it to engage the engine. If your snowblower is electric, plug it in and press the "start" button. Finally, turn the choke to the “off” or “run” setting. For tips on inspecting your snowblower before using it, read on!
Did this summary help you?
Thanks to all authors for creating a page that has been read 114,450 times.
Advertisement
