Download Article
Download Article
Whether you want to learn how to tie a fisherman's knot for climbing, search and rescue, or just because you like tying knots, it's relatively simple to learn how. As long as you're willing to commit to a little bit of practice you'll be tying fisherman's knots in no time.
Steps
-
Find the tag end of your rope. This is the end of your line and the part that will be doing the knot tying. [1] X Research source Designate the end of your rope before you start.
-
Learn the meaning of standing line. This is the rest of your line that would run up toward a reel if you were fishing, or a cinch if you were rock climbing. Basically it is all the middle section of your rope.Advertisement
-
Understand the turn. The turn is when the end of the rope – the tag end – passes completely around the standing line. Some call this a wrap. [2] X Research source
Advertisement
-
Grab hold of both ends of the rope. The end in your left hand is end 2, and the end in your right hand is end 1. End 1 will be doing the knot tying, so recognize this as the tag line. [3] X Research source
- Make sure you give yourself plenty of slack. It's helpful to have a lot of string or rope to work with as you learn.
-
Cross end 2 in front of end 1. You want to cross them so that end 2 lies over end 1. The end of the tagline (end 2) will be behind the loop you have created and pointing downwards. You can leave a short tail or a long tail depending on how much rope you have. To start, make sure that you have at least 6 inches (15 cm) of rope to do the tying. This means that you should have 6 inches (15 cm) of rope above where you crossed it.
-
Pull the tagline through the loop you've created. [4] X Research source You've crossed your two lines, so one line should be dangling over the other. Take the dangling piece and start to wrap it around the other piece. As you do this, the part of rope that you originally crossed will start to form a loop. So instead of wrapping that dangling piece (end 2) around end 1, pull end 2 through the loop and up to the left. This will create a smaller loop on top of the larger loop underneath. Keep the loops loose so you're able to get the line through the hole.
-
Pull the tagline through the smaller loop. Using your right hand, pull end 2 through the smaller loop. You should enter the smaller loop from the back and pull up to the front.
Advertisement
-
Start to tighten the loop you made. You can tighten the loop by pulling the tagline with your right hand and end 1 with your left hand. End 1 will be next to the bigger loop at this point. [5] X Research source
- This will create a knot on top of your larger loop. End 1 should be able to slide back and forth enabling you to adjust the loop to the appropriate size. If you have ever tied a tie before, it's a similar concept to the tightening of a tie.
-
Create another small loop. To continue tightening your knot, pull end 1 through the large loop from behind. Imagine a tie that has already been tied. If you were following instructions to make a tighter fisherman's knot, you would take the bottom of the tie and stick it in through the top of the knot that is holding your tie in place. Once you've done this, pull the line upwards once again. This will proceed to make another small loop on top of the larger loop you just pulled your rope through.
-
Pull end 1 through the smaller loop from behind. Make sure you pull it through the loop from behind. Pull the loop to tighten it using your left hand.
-
Tighten the final loop. [6] X Research source Just like you tightened the first knot, tighten this knot by pulling the larger loop from either side. If you plan to undo your work and try again, then you probably shouldn't pull too hard or it will be hard to untie the knot.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Make sure you have someone test your knot before you do something dangerous like climbing, especially if you are a beginner.Thanks
- One variation of this knot is to wrap the tagline around the standing line eight to ten times before following the same knot tying process. This helps if you have a lot of extra line.Thanks
- You can practice this knot with string, or wire, or twine, or any other string-like material. It doesn't need to be a rope.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
References
- ↑ http://www.dummies.com/how-to/content/tying-the-fishermans-knot.html
- ↑ http://www.dummies.com/how-to/content/tying-the-fishermans-knot.html
- ↑ http://www.netknots.com/rope_knots/double-fishermans/
- ↑ http://www.dummies.com/how-to/content/tying-the-fishermans-knot.html
- ↑ http://www.dummies.com/how-to/content/tying-the-fishermans-knot.html
- ↑ http://www.indoorclimbing.com/Fishermans_Knot.html
About This Article
Article Summary
X
To tie a fisherman’s knot, grab the ends of the rope in your hands, where the right hand is end 1, and the left hand is end 2, or the “tagline” which does the tying. First, cross end 2 over end 1 and pull end 2 downward and around end 1 to create a loop. Then, pull end 2 through the loop you just made to create a smaller loop inside of the original loop. Pull end 2 through the back of the smaller loop to the front to complete the knot. If you want to learn how to make your knot tighter, keep reading the article!
Did this summary help you?
Thanks to all authors for creating a page that has been read 62,960 times.
Advertisement
