How to Turn Off MAC Filtering

PDF download Download Article
PDF download Download Article

MAC (Multimedia Access Control) addresses are unique sets of codes assigned to electronic devices that identify the devices on a network. MAC filters work by either allowing or denying only specific MAC addresses. MAC filters are a great security measure; however, if your network needs to be open to public or guests, or you're adding and removing devices often, then you should consider turning off MAC filtering.

Method 1
Method 1 of 3:

Windows

PDF download Download Article
  1. You can access it from the Start menu, or by pressing ⊞ Win + R and typing cmd .
  2. ipconfig and press ↵ Enter .
    Advertisement
  3. There may be several connections listed in the readout, and you may have to scroll up to find your active connection.
  4. Default Gateway entry. This is the address for your router. Write it down.
  5. You can access your router's configuration page from any web browser as long as your computer is connected to the network.
  6. Default Gateway address into the browser's address bar.
  7. Routers are protected with an admin login and password. Check your router's documentation or look up the model online to find the default login information.
    • If you can't figure out how to log in to your router, you can reset it by pressing and holding the Reset button on the back for about 30 seconds. After the router restarts, you will be able to log in with the default admin information.
    • Most default logins use "admin" as the username, and then "admin", "password", or a blank field as the password.
  8. Actually defining where the "MAC Filtering" section is located is very difficult, as the location and labeling is different for every router. Generally, you can find the "MAC Filtering" or "Access Control" settings in the "Advanced" section, though it may also be found in the "Security" or "Wireless Settings" sections.
    • Not all routers use MAC address filtering. Some router's limit access based on static IP addresses assigned to each device.
  9. Again, the wording and location will vary depending on the router, but you will generally be able to select a "Disable" option to turn off MAC filtering.
    • This may be a checkbox, a button or a selection that you can make.
  10. Click the "Apply" or "Save" button to save your changes to the router settings. Your router will apply the changes, which may take a few moments.
    • If you are configuring your router over a wireless connection, you may be logged out when settings changes are saved.
    11. Advertisement
Method 2
Method 2 of 3:

macOS (AirPort)

PDF download Download Article
  1. You can access this from the Go menu, or from your Applications folder.
  2. This program allows you to easily configure your AirPort router without having to use a web browser interface.
  3. If you have multiple AirPort routers installed on your network, select the one you want to make changes to and click Edit .
  6. Update . This will save the changes for your AirPort router, disabling MAC filtering.
    7. Advertisement
Method 3
Method 3 of 3:

macOS (Other Routers)

PDF download Download Article
  3. Connected adapters will have a green indicator next to them.
  4. Router IP Address. This is the address that you can use to access your router's settings.
    • If you are using an AirPort router, click here.
  5. Router address into the browser's address bar.
  6. Routers are protected with an admin login and password. Check your router's documentation or look up the model online to find the default login information.
    • If you can't figure out how to log in to your router, you can reset it by pressing and holding the Reset button on the back for about 30 seconds. After the router restarts, you will be able to log in with the default admin information.
    • Most default logins use "admin" as the username, and then "admin", "password", or a blank field as the password.
  7. Actually defining where the "MAC Filtering" section is located is very difficult, as the location and labeling is different for every router. Generally, you can find the "MAC Filtering" or "Access Control" settings in the "Advanced" section, though it may also be found in the "Security" or "Wireless Settings" sections.
    • Not all routers use MAC address filtering. Some router's limit access based on static IP addresses assigned to each device.
  8. Again, the wording and location will vary depending on the router, but you will generally be able to select a "Disable" option to turn off MAC filtering.
    • This may be a checkbox, a button or a selection that you can make.
  9. Click the "Apply" or "Save" button to save your changes to the router settings. Your router will apply the changes, which may take a few moments.
    • If you are configuring your router over a wireless connection, you may be logged out when settings changes are saved.
    10. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What if I don't have ethernet, but I have wifi?
    Community Answer
    It will still work.
    Thanks! We're glad this was helpful.
    Thank you for your feedback.
    If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 10 Helpful 0
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Name
      Please provide your name and last initial
      Submit
      Thanks for submitting a tip for review!
      Advertisement

      You Might Also Like

      How to
      Turn Off Mac Firewall
      4 Simple Ways To Add an HP Printer to a Wireless Network
      How to
      Find the MAC Address of Your Computer
      How to
      Check if a Port is Open: 5 Quick Ways
      How to
      Forward a Port on Any Router: Easy Guide
      Connect Two Computers: Microsoft Windows & Mac OS X
      How to
      Flush DNS (Clear the Cache) in All Major Operating Systems
      3 Ways to Change a Computer's Mac Address in Windows
      How to
      Get a MAC Address from an IP Remotely
      How to
      Create a Local Area Network (LAN)
      How to
      Join a Domain on a Windows Computer or Mac
      Easy Ways to Set Up and Connect to a Local Area Network (LAN)
      How to
      Connect One Router to Another to Expand a Network
      How to
      Set up a Shared Network Drive
      Advertisement

      About This Article

      Article Summary X

      1. Log in to your router's admin site.
      2. Navigate to Advanced .
      3. Navigate to Mac Filtering or Access Control .
      4. Select the option to disable filtering.
      5. Click Apply or Save .

      Did this summary help you?
      In other languages
      Thanks to all authors for creating a page that has been read 277,468 times.

      Is this article up to date?

      Advertisement