Download Article
Download Article
Hook-and-loop fasteners, such as the Velcro® brand fasteners, are a breeze to use but can be difficult to keep clean. Clothing fuzz, pet hair and other lint can get embedded in the hook side of the closure, diminishing its ability to close. By removing surface fuzz, picking out embedded lint and performing hook-and-loop fastener maintenance, you can keep your closures clean and working well.
Steps
-
Roll the hook-and-loop fastener with a lint roller. To remove surface debris, use a lint roller that you’d normally use on your clothes to roll the fastener. Lay the fastener flat, and hold at one end, rolling over it a few times with the lint brush. Refresh to a new sticky “sheet” of the lint roller as necessary. [1] X Research source
-
Press the hook-and-loop fastener with duct tape. Cut a piece of duct tape no bigger than your palm, so it doesn’t get unwieldy and stick to itself. Lay the fastener flat, and press the tape into the closure to get it to adhere to as much lint as possible. Holding the fastener firmly at one end, strip the tape away to remove the lint.
- You can perform this step several times with new pieces of duct tape, as necessary.
Advertisement -
Use your fingernails to scrape the hook-and-loop fastener. Your fingers can be a useful tool to remove any surface lint from the fastener. Lay the fastener flat, and pick off any obvious pieces of thread or hair that may have ends you can grab sticking over the edge. Then, give the fastener a good scrape with your fingernails to remove as much surface lint as you can.
Advertisement
-
Use a stiff toothbrush to brush the hook-and-loop fastener. Use a stiff, plain toothbrush (preferably just bristles no gum massagers or other plastic parts) to brush trapped lint out of the fastener. Lay the fastener flat, and apply pressure in short, hard strokes with the bristles from one end of the fastener to the other. [2] X Expert Source James Sears
Professional Cleaner Expert Interview. 28 August 2019.- Pick any lint that comes to the top of the fastener out with your fingers.
-
Scrape the hook-and-loop fastener with the cutter of a tape dispenser. Use the edge of the tape dispenser that you'd normally use to cut the tape to scrape the fastener clean. Lay the fastener flat, and use the teeth of the tape dispenser to rake it in short firm strokes from one end to the other. [3] X Research source
- Pick any lint that comes to the top of the fastener out with your fingers.
-
Pick any deep lint out with needle-nose tweezers. For lint that is deeply embedded in the hooks of the fastener, use a pair of needle-nose tweezers to pick it out. Lay the fastener flat, holding at both ends. Then, use the tips of the tweezers to tease out the debris. [4] X Research source
Advertisement
-
Brush lint out of the hook-and-loop fastener once a month. To keep the fastener closing well and lint-free, clean it once a month. Doing this will keep debris from getting excessively embedded, which is more difficult to remove than surface lint. [5] X Expert Source James Sears
Professional Cleaner Expert Interview. 28 August 2019. -
Fasten the hook-and-loop fastener together before placing it in the washer. If the fastener is on an item you wash in the washing machine, fasten the hook and loop sides together before washing the item. This will keep the closure from picking up stray threads or damaging your other clothes in the washing process.EXPERT TIPProfessional CleanerJames Sears leads the customer happiness team at Neatly, a group of cleaning gurus based in Los Angeles and Orange County, California. James is an expert in all things clean and provides transformative experiences by reducing clutter and renewing your home environment. James is a current Trustee Scholar at the University of Southern California.
Our Expert Agrees: You can clean most Velcro items in your washing machine, but be sure to fasten the Velcro together to prevent the collection of more debris, hair, and lint. Also, if the Velcro is glued to the item, rather than stitched or sewn in place, you may want to avoid machine drying, or at least dry it on low heat. Drying the object on high heat can cause the glue to melt or wear off over time.
-
Spray the hook-and-loop fastener with anti-static spray after washing. Anti-static spray, such as Static Guard, can make the fastener attract less lint. Spray the fastener after you wash your clothes, to minimize debris.
Advertisement
Community Q&A
Search
-
QuestionCan I iron Velcro?Community AnswerYes, and no. You have to buy the iron on kind of Velcro. You cannot iron the sticky kind. It should specifically state on the package what kind it is.
-
QuestionWhere can I buy the spray anti-static spray?Community AnswerLook up Static Guard and you can order it online or buy it in places Walmart. There might be other brands, but this is a common one.
-
QuestionWhere can I buy the brush to clean Velcro?Community AnswerYou can use any hard-bristled toothbrush. You can find them at your local pharmacy or a dollar store. They might be a little hard to find because most dentists recommend soft-bristled toothbrushes.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
References
- ↑ https://startsat60.com/lifestyle/how-to-remove-lint-from-your-clothes-without-a-lint-roller
- ↑ James Sears. Professional Cleaner. Expert Interview. 28 August 2019.
- ↑ https://www.youtube.com/watch?v=ymrTyEk7UiU
- ↑ https://www.trails.com/how_1049_clean-velcro.html
- ↑ James Sears. Professional Cleaner. Expert Interview. 28 August 2019.
About This Article
Thanks to all authors for creating a page that has been read 590,764 times.
Reader Success Stories
- "It was helpful to discover this problem can be resolved and performance of old velcro improved. Because I only had a small area to address, I used a needle and it seemed to be effective as I was able to restore some functionality to a thin velcro closure." ..." more
Advertisement
100%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"It was helpful to discover this problem can be resolved and performance of old velcro improved. Because I only had a small area to address, I used a needle and it seemed to be effective as I was able to restore some functionality to a thin velcro closure."
..."
more
"It was nice to hear that others have the same problem. I have 6 dogs and my foot brace just goes along gathering hair. I have plenty of dog brushes, I will try that first, then your illustrated pictures with a toothbrush. Great ideas and worth the time."
..."
more
"The tips were excellent and it took me far less time than I had thought it would. I used tweezers, my fingers, and a sharp tool like the kind dentists use to pick at your teeth. I had five Velcro straps on a "boot" I had to wear for my ankle."
..."
more
"Using tape and a bristled brush worked to get the debris out of my wrist brace so I could use it again without having to buy a new one! One of the velcro parts is still kind of not sticking well, but overall it worked!"
..."
more
"I hadn't thought about using most of the suggestions in this article until reading this. Said to myself, "Now why didn't I think of that". Thank you, wikiHow!"
..."
more
