Download Article
Download Article
Downshifting a motorcycle can be accomplished in several ways. First, you can simply pop it down a gear without using the clutch by putting a little pressure on the shifter and closing the throttle. This method is not particularly recommended as it is hard on the bike. Second, you can pull the clutch in, select the next gear, then let the clutch out slowly to smooth the transition. Perhaps the best method, though, is the matched rev downshift method described below.
Things You Should Know
- Use your index and middle fingers to brake while keeping your ring and pinky fingers on the throttle.
- Pull in the clutch and select the next gear.
- Still holding the clutch in, use the palm of your hand and/or your ring and pinky fingers to rev the engine slightly.
- Let the clutch back out to engage the next gear.
Steps
Download Article
-
You will have to be used to using the front brake with only one or two fingers in order to downshift this way. It is best to use your index and middle fingers to brake while keeping your ring and pinky fingers on the throttle. [1] X Research source -
After you begin braking, pull in the clutch and select the next gear like you would normally.Advertisement
-
Here is the tricky part. Still holding the clutch in, use the palm of your hand and/or your ring and pinky fingers to rev the engine slightly. [2] X Research source
-
Remember to keep braking smoothly with your index and middle fingers. [3] X Research source
-
When the engine is revved up slightly, let the clutch back out to engage the next gear. The goal here is to match the revolutions of the engine to what they need to be to travel the same speed in the lower gear. This smooths the transition between gears and eliminates the need to slip the clutch quite as much. [4] X Research source
-
If the bike jerks forward when you let the clutch out the engine was turning too fast. Don't rev it as much next time.
-
If the bike rapidly slows, the engine wasn't turning fast enough so you need to rev it more before releasing the clutch.
-
Repeat each time you shift down a gear. This technique is especially useful in the lower gears, which generally have a wider gap between gear ratios.
-
Finished.
Advertisement
Community Q&A
Search
-
QuestionDo you have to brake while rev matching, or can you rev match without brake?Community AnswerYes you can do it without braking, no matter why you're going down a gear, blip the throttle. If you're coming to a stop or slowing down, always use at least a little brake just so people behind see your brake light so they know what you are doing.
-
QuestionDo dirt bikes have to rev match too?CrayFish715Community AnswerNo, not really. Rev matching is a performance riding technique, so you don't have to do it on any bike. It's tricky to do rev matching on a dirt bike as they are single cylinder, and the power doesn't come on and off gently.
-
QuestionDoes it spoil the bike if one downshifts too fast while slowing down?Community AnswerNo, but you'll get engine braking, which is when the bike is trying to go faster than the selected gear will allow. It's likely to throw you forward a bit depending on the speed and the gear, so if you drop into a particularly low gear at a high speed it can be quite dangerous.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Video
Tips
- Practice makes perfect. If you don't get this right away, keep trying, eventually it becomes second nature.Thanks
- If you are just learning to ride, I would recommend learning to brake with two fingers, but not worrying about this method of downshifting until you are more comfortable on the bike.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- Find an empty lot or road with little traffic when first learning this technique, or any other new maneuver on a motorcycle for that matter.Thanks
- Do not practice shifting techniques while turning, if you cause the bike to jerk during the shift you could throw yourself out of balance and potentially crash. It's best to practice while going straight and level.Thanks
Advertisement
References
- ↑ https://drivingfast.net/rev-matching-for-motorcycle-riders/
- ↑ https://www.youtube.com/watch?v=_3mans3ZsMo
- ↑ https://www.motorcyclistonline.com/motorcycle-shifting-tips/
- ↑ https://www.youtube.com/watch?v=yDLWmzomvZA
- https://www.ridinginthezone.com/10-things-you-need-to-know-about-throttle-blipping/
About This Article
Thanks to all authors for creating a page that has been read 289,387 times.
Reader Success Stories
- "This helpful information could save me from serious injury and trashing my bike. I've had previous bad experiences with the back wheel locking up or engine braking whilst downshifting and I almost lost control. " ..." more
Advertisement
91%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"This helpful information could save me from serious injury and trashing my bike. I've had previous bad experiences with the back wheel locking up or engine braking whilst downshifting and I almost lost control. "
..."
more
"Great to see the full techniqe explained with fab graphics. I wasn't confident about the 2 finger breaking, but I now have the confidence to practice. Doing this makes a huge difference to control. Thanks."
..."
more
"It's the clearest explanation I've found of this technique. Steps 2 and 5 are key aspects very often missed."
..."
more
"Very nice, I had doubts about downshift, throttle blipping, rev matching."
"When to downshift gears helped."
