Download Article
Download Article
Plastic gas tanks are in high demand in the world of motorcycle racing and ATV enthusiasts. A plastic gas tank can weigh less than half of a comparable metal gas tank and it is easy to mold into shapes to fit odd configurations. Seamless gas tanks seldom leak and are impervious to the rust and corrosion that affect metal tanks. If a plastic fuel tank does sustain small holes or tears, there are several fairly easy ways to make the repair.
Steps
-
Drain the gasoline from the tank and allow it to dry. Sand the area around the hole or crack, and clean the area with a shop cloth saturated with rubbing alcohol. [1] X Research source
-
Mix the 2 part epoxy together and apply all around the perimeter of the opening. [2] X Research source Cut a fiberglass patch large enough to cover the opening and overlap it.Advertisement
-
Place the fiberglass patch over the hole and press into the epoxy. Apply more epoxy to the patch and surrounding area, pressing firmly to saturate the patch.
-
Allow to dry, sand the patched area smooth and spray paint with a plastic paint if desired.
Advertisement
-
Buy or rent a plastic welder. Tell the salesperson what you are doing with it to ensure that you get the correct rods.
-
Remove the plastic gas tank from the vehicle, and set it up in a secure welding area. Drain the gasoline from the tank, and allow it to dry both inside and outside. Don protective eye gear, a welding helmet and welding gloves.
-
Use a plastic welding rod made specially for this purpose, and fill in the crack or hole. Start at an edge and run the bead completely around the opening. Then begin crossing over the hole, allowing the rod to fill in the hole completely. [3] X Research source
-
Allow the weld to set up, sand it smooth and, if desired, paint it with plastic spray paint.
-
Replace the repaired plastic fuel tank on the vehicle.
Advertisement
-
Drain the gas tank, and clean it inside and out with soapy water. [4] X Research source Lightly sand the perimeter of the area to be repaired.
-
Cut a plastic patch, made of a similar material to the gas tank, slightly larger than the hole to be repaired.
-
Heat up an electric soldering gun, and drag it around the edge of the crack to create a trench. Move the gun from side to side to push the plastic back into the trench. While the plastic is still soft from the soldering, lay the plastic patch over the area. Continue moving the soldering gun over the area to smooth the plastic, and fuse them together. [5] X Research source
-
Allow to cool and dry completely. Mix a 2 part epoxy glue, and cover the entire area of the patch. [6] X Research source Allow to set up, sand and spray on a coat of plastic paint if desired.
Advertisement
Community Q&A
Search
-
QuestionIs Flex Seal gasoline resistant?This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.wikiHow Staff EditorStaff AnswerAccording to the manufacturer’s website, Flex Seal is not a good choice for sealing gasoline tanks. It’s not made to withstand a lot of heat or pressure, and it’s not recommended for use with flammable liquids, such as gasoline.
-
QuestionHow do you fix a plastic gas tank on a lawnmower?This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.wikiHow Staff EditorStaff AnswerA fiberglass repair patch will work well for this job. Drain the tank and let it dry completely first, and don’t forget to sand the area around the leak or hole so that the adhesive compound can adhere properly.
-
QuestionWill Teflon tape seal in gasoline?This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.wikiHow Staff EditorStaff AnswerNo, the gasoline will eventually break down the tape. If you want a quick and easy fix, a fiberglass patch is a better option.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- Using epoxy glue is the easiest way to seal a plastic fuel tank, but it sometimes fails after a short time.Thanks
- If using a plastic welder for the first time, practice before attempting to seal the plastic gas tank. The rental store should be able to work with you to ensure that you have no problems.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement
Warnings
- A plastic welder is safe around gasoline and gasoline fumes, as it has a very high flash point. However, use common sense and do not use near open flames.Thanks
Advertisement
Things You'll Need
- Plastic patches
- 2 part epoxy glue
- Fiberglass patch
- Sandpaper
- Shop cloth
- Rubbing alcohol
- Plastic spray paint
- Plastic welder
- Welding rods
- Welding helmet
- Welding gloves
- Eye protection
- Soldering gun
References
- ↑ https://car-repair.carsdirect.com/car-repair/how-to-repair-a-leaking-gas-tank
- ↑ https://car-repair.carsdirect.com/car-repair/how-to-repair-a-leaking-gas-tank
- ↑ https://youtu.be/Lqu3NVqFNCU?t=79
- ↑ https://youtu.be/EbtUxJJs8G0?t=85
- ↑ https://youtu.be/EbtUxJJs8G0?t=140
- ↑ https://youtu.be/EbtUxJJs8G0?t=421
About This Article
Article Summary
X
To seal a plastic gas tank with epoxy glue, start by draining the tank and letting it dry. Then, sand the area around the hole or crack with coarse grit sandpaper, and clean it with a cloth soaked in rubbing alcohol. Next, mix the epoxy glue, apply it over the opening, and press a fiberglass patch over the epoxy. Let the epoxy dry, then smooth out any bumps or unevenness with sandpaper, and spray paint with plastic paint if desired. To learn more, including how to seal a plastic gas tank with a plastic welder or soldering gun, scroll down.
Did this summary help you?
Thanks to all authors for creating a page that has been read 475,172 times.
Reader Success Stories
- "It answered questions about materials and cleaning. I've used epoxy and fiberglass many times to repair a number of things over the years." ..." more
Advertisement
80%
of readers found this article helpful
.
Click a star to add your vote
% of people told us that this article helped them.
"It answered questions about materials and cleaning. I've used epoxy and fiberglass many times to repair a number of things over the years."
..."
more
"I have a 3-horsepower gas tank Gamefisher. It fell too many times and cracked everywhere, I'm going to try this product and see."
..."
more
"I have a plastic gas tank on my mower that has a cut in it. This helps. "
"Have not used it yet, but info is useful."
