Download Article
Download Article
For many people, tree swings are a comforting reminder of the joys of childhood. If you want add a special touch to your yard, you can hang your very own swing from a sturdy tree. There are 2 different ways to hang a tree swing. Drilling an eye bolt into the tree is the safest for the tree, but it requires specialized tools. You can also just tie the rope directly to the tree, but this may cause damage to the tree over time.
Steps
-
Select a hardwood tree. Sturdy, hardwood trees are the best for installing swings. These include oak trees, sugar maples, or ash trees. Avoid putting swings on pine trees or fruit trees. [1] X Research source
-
Evaluate the condition of the tree and branches. Both the tree and the individual branch need to be healthy and strong to hold a swing. Make sure that the tree is not diseased or infested with bugs. The branch should not be cracked or peeling. Never attach a swing to a dead branch. [2] X Research source
- If you’re uncertain about the condition of the tree, ask an arborist to check it out for you.
Advertisement -
Find a long branch that is parallel to the ground. The branch should make an “L” shape as it extends from the tree. You will need a branch that is at least 6 feet (1.8 m) long. [3] X Research source
- The branch should not be more than 20 feet (6.1 m) off the ground.
- The swing will need to be at least 3–5 feet (0.91–1.52 m) away from the trunk so that it does not hit the tree. It also shouldn't, however, be near the end of the branch, where it is weakest. The branch should be very strong in the middle.
-
Look for a branch that is at least 8 inches (200 mm) in diameter. The branch needs to be thick enough that it will not break under the force the swing exerts. Make sure that the branch does not get significantly narrower as it goes out from the tree. [4] X Research source
Advertisement
-
Find eye bolts that are 5 ⁄ 8 inch (16 mm) in diameter. You can use larger eye bolts but not smaller. Get stainless or galvanized steel eye bolts that are longer than the branch is thick. If your branch is 8 inches (200 mm) thick, find an eye bolt that is longer than 8 inches (200 mm) [5] X Research source
-
Drill holes on the underside of the branch. Place the holes about 3–5 feet (0.91–1.52 m) away from the trunk. Make them slightly larger than the screw’s diameter. So if you used 5 ⁄ 8 inch (16 mm) bolts, drill a hole that is about 3 ⁄ 4 inch (19 mm) in diameter. Drill all the way through the center of the branch. [6] X Research source
- If you are hanging a tire swing or a disc swing, you may only need 1 hole.
- If you are hanging a rectangular swing, you will need 2 holes. The distance between the holes should be slightly larger than the swing. This will help stabilize the swing. [7] X Research source
- You will likely need a ladder to reach the branch. Make sure that you have someone spotting you as you use the ladder.
-
Screw the eye bolts in on the underside of the tree. Place the shank of the eye bolt into the hole under the branch. The loop should face down towards the ground. Turn the bolt in all the way. The end of the bolt should stick out the top of the branch. Screw a washer and a nut down onto the threads until they are pressed against the branch. This will secure the bolt to the tree.
- After you install the swing, check the eye bolts regularly to make sure that they are in good condition. If the bolts have rusted or bent, replace them.
- Healthy trees will grow around the eye bolts. If the wood is cracking near the bolts, however, you may need to move the swing to a different branch.
-
Attach an S-hook, quick link, or carabiner to the eye bolt. No matter what type of hardware you use, make sure it is the highest possible weight rating that you can get. [8] X Research source
- If you use an S-hook, hook 1 loop on top; the bottom hook will be used for the rope.
- Unscrew the quick link and hook it on to the eye bolt before screwing it closed.
- If you use a carabiner, clip it through the loop.
-
Knot the rope onto the link. Use a braided polyester rope with as high a weight rating as possible. You can attach the rope to the hook, link, or carabiner using a double square knot or a double running bowline knot . [9] X Research source
- You will need at least as much rope as the branch is high, plus a few extra feet just to be safe.
- Do not attach the rope to the swing yet. It is fine if the swing came with the rope already attached, but it is easier to hang the rope without the swing attached.
- Alternatively, you can attach a metal chain to the link for the swing instead. Simply hook or loop the chain onto the link.
-
Attach the swing to the other end of the rope. Place the rope through the holes of the swing. Adjust the height until it is to your satisfaction. Knot the rope using a bowline knot. Cut off any extra rope. [10] X Research source
- If the swing is for a child, you may need to set the seat about 13 inches (330 mm) off the ground. If it is for adults, make it the same height as the seat of your pants.
Advertisement
-
Use a braided polyester rope. Polyester rope is strong enough to hold up the swing, but it won’t fray or fade in the elements. When purchasing rope, make sure that you get the highest weight rating possible. [11] X Research source
- Unless the swing came with the rope already attached, do not attach the rope to the swing yet.
- If your swing came with a metal chain attached, you must attach it using an eye bolt. You cannot tie a chain to a tree.
-
Loop the rope over the tree branch. Use a ladder to reach the tree branch and toss the rope over the branch. Make sure that the rope is at least 3–5 feet (0.91–1.52 m) away from the trunk. [12] X Research source
-
Secure the rope using a bowline knot. Make 2 loops with the rope. Place one end through the loops, then wrap it under the second end of the rope. Bring the first end back over the second end and put it back through the double loop. Pull both ends until tight.
- Leave about 3 inches (76 mm) of tail at the end of the knot. [13] X Research source
- It is a good idea to check the knot regularly after putting the swing up. Make sure that the knot is still tight. If the rope is fraying, replace it.
-
Attach the swing to the other end of the rope. Stick the ends of the rope through the holes of the swing. Move the swing up the rope until the height is right. Make a bowline or figure eight knot immediately under the swing, and cut off any extra rope. [14] X Research source
- If the swing is for a child, you can place the seat about 13 inches (330 mm) off the ground.
- If adults will be using the swing too, try to find a height based on what would be comfortable for you.
Advertisement
Community Q&A
Search
-
QuestionCan I leave a swing up during the winter?Community AnswerYes, you can.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement
Tips
- You may need to replace the rope every few years.Thanks
- To keep the swing in good shape, remove it from the tree and store it over the winter.Thanks
- You can buy tree swing hanging kits online. These often include straps that you can hook a swing to.Thanks
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Warnings
- If the branch bends or bounces while someone is using the swing, it may mean that the branch is not strong enough to support the swing. Move it to a different branch.Thanks
- If you notice that the rope is starting to fray, replace the rope immediately.Thanks
- If the branch starts to peel or crack, move the swing to different branch.Thanks
Advertisement
Things You’ll Need
- Eye bolts
- Drill
- Washers and nuts
- Measuring tape
- Extension ladder
- Polyester rope
- Metal Chain
- Swing
References
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.thisoldhouse.com/ask-toh/hanging-tree-swing
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.thisoldhouse.com/ask-toh/hanging-tree-swing
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.motherearthnews.com/diy/how-to-make-a-tree-swing-zmaz92aszshe
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.motherearthnews.com/diy/how-to-make-a-tree-swing-zmaz92aszshe
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.todayshomeowner.com/how-to-install-a-tree-swing-safely/
- ↑ https://www.motherearthnews.com/diy/how-to-make-a-tree-swing-zmaz92aszshe
- ↑ https://www.motherearthnews.com/diy/how-to-make-a-tree-swing-zmaz92aszshe
About This Article
Article Summary
X
To hang a tree swing, start by selecting a sturdy, hardwood tree with healthy branches. Next, locate a a strong branch that is parallel to the ground, at least 6 feet long, and no more than 20 feet off the ground. You can then hang the swing by using eye bolts and a drill or by looping a braided polyester rope over the branch and securing it with a tight, durable knot. For specific instructions on using eye bolts to hang the swing, read on!
Did this summary help you?
Thanks to all authors for creating a page that has been read 115,875 times.
Advertisement
